Moeller low-permeation fuel line assembly - 3/8". Meets EPA requirements for fuel lines. Solid hydrocarbon and solvent resistant construction. Dual internal check valves ensure a rapid prime while ensuring that there is no fuel flowback. Includes primer bulb, clamps, and hardware. Uses O-rings on all fittings to prevent leaks. Moeller item number 034391-10. Intended for use with 3/8" lines. For Bombardier Johnson / Evinrude motors. Weight: 1 lb.

Dual cable clip bracket for use with 33C
throttle and shift cables.

Rubber-lined brass sleeve bearing. Adapts well to struts and stern-tube mounts. Precision fitted for shafts with proper clearance. Brass shells, chemical-resistant nitrile rubber interiors. Stocking name: CORD. Shaft/sleeve size: 2-1/2". Outside diameter: 5-1/8". Length: 10". Weight: 4.38 lbs.

Rubber-lined brass sleeve bearing.
Adapts well to struts and stern-tube mounts.
Precision fitted for shafts with proper clearance.
Brass shells, chemical-resistant nitrile rubber interiors.
Stocking name: CORN.
Shaft/sleeve size: 2-1/2".
Outside diameter: 3-3/8".
Length: 10".

Eye terminal for 30C series cable.
5/16" eye, 10-32 threads.  
Aluminum construction.
Replaces Morse eye terminal  31980.

Pin only, for connecting terminal eye to control and slave.
1-1/2” overall length.  
5/16” dia. stud, 19/32" overall length, 1/4-28 threads.
Brass construction.

Ball joint with quick release stud.
Plated steel.
For 40 series cable.
1/4" stud.

Ball joint with quick release stud.
Plated steel.
For 60 series cable.
5/16" stud.

Cable clevis, pin, & cotter pin for 60 series control cable.
Pin diameter: 5/16".
Plated steel.

Reinforced polypropylene and metal construction. Suction cups attach to side water inlets or intake. May be used to run motor while out of water. Attaches easily to garden hose.

Stainless steel replacement lever for
SeaStar CH5400P & CH5600P engine controls.  
Does not include knob.  
Length: 7-3/4”.

Single adjustment.
Reduces relief setting and assists purging.

Rated for 950 PSI.

Port size: 1/4".

Cable clevis, pin, & cotter pin for 40 series control cable.
Pin diameter: 5/16".
Plated steel.

30 series cable clamp.
Used with 31538 shim.
1" center to center bolt pattern.
Plated steel.

40 series cable clamp.
1" center to center bolt pattern.
Used with 31538 shim.
Plated steel.

30 series.
Stud diameter: 1/4".
Lever thickness: 3/16".
Length: 23/32".

Cable clamp shim for 30 and 40 series control cables.
1" center to center bolt pattern.
Overall dimensions: 1-1/2" X 1/2".
Plated steel.

40 series.
Stud diameter: 1/4".
Lever thickness: 3/16".
Length: 7/8".

Designed for harsh environments.
Stainless steel keyboard.
Submersible.
Covered by an extended warranty.

Rubber-lined brass sleeve bearing. Adapts well to struts and stern-tube mounts. Precision fitted for shafts with proper clearance. Brass shells, chemical-resistant nitrile rubber interiors. Stocking name: CALM. Shaft/sleeve size: 2". Outside diameter: 3". Length: 8". Weight: 3.81 lbs.

Rubber-lined brass sleeve bearing. Adapts well to struts and stern-tube mounts. Precision fitted for shafts with proper clearance. Brass shells, chemical-resistant nitrile rubber interiors. Stocking name: CALL. Shaft/sleeve size: 2". Outside diameter: 2-5/8". Length: 8". Weight: 2.88 lbs.

Universal rectangular cup motor flusher unit. No tools required, just slip over inlets. Quickly removes build-up with a simple flush. Removes contaminates from lower unit cooling systems. For use on all lower units with side water inlets. Product # 099076-00.

Rubber-lined brass sleeve bearing. Adapts well to struts and stern-tube mounts. Precision fitted for shafts with proper clearance. Brass shells, chemical-resistant nitrile rubber interiors. Stocking name: CART. Shaft/sleeve size: 2-1/4". Outside diameter: 3-1/8". Length: 9". Weight: 4.13 lbs.

Manganese bronze construction. Length: 9". Shaft size: 1-1/4". Key way: 1/4".

Ball joint with quick release stud.
Plated steel.
For 30 series cable.
10-32 stud.

T-Style handle, 10-32 threads.

Non-metallic sleeve bearing. Features a dense, reinforced thermoset plastic shell. Precision fitted to 1-1/2" nitrile rubber shaft. Completely non-corrosive, perfect for specific installations Outside diameter: 2". Length: 6". Weight: .5 lb.

Non-metallic sleeve bearing. Features a dense, reinforced thermoset plastic shell. Precision fitted to 2-1/4" nitrile rubber shaft. Completely non-corrosive, perfect for specific installations Outside diameter: 3". Length: 9". Weight: 1.5 lbs.