Schroeder on-board coalescing diesel fuel filter.
Features an automatic drain design.
Low investment cost due the economical design.
Long service life of the element yields low operating costs.
Seamless installation due to the plug and play.
Easy adaption to the on-board power supply.
Unsurpassed water removal for ULSD.
24 volt DC.
2.6 GPM.
Port size: 3/4" BSP.

Replacement filter element.
5 micron.
Appropriate for drinking water.

Outboard complete filter 2 Micron element, see-thru bowl, primer bulb Max flow rate: 60 GPH/340 Iph Center threads: 1-14 Head port size: 3 Clean pressure drop: 30 PSI/207 kPa Element removal underbowl: 1"/25.4 mm Max Pressure: 7 PSI/48 kPa Operating temp: 1"/25.4 mm Height: 9.38" X 4" X 4".

Inboard/Outboard complete filter 2 Micron element, see-thru bowl, primer bulb Max flow rate: 60 GPH/340 Iph Center threads: 1-14 Head port size: 3 Clean pressure drop: 30 PSI/207 kPa Element removal underbowl: 1"/25.4 mm Max Pressure: 7 PSI/48 kPa Operating temp: 1"/25.4 mm Height: 9.38" X 4" X 4".

Engineered to repel water and remove contaminates.

For model 230 filter assemblies.

Filter is 2 microns.

Rated for 30 GPH.

Turbine series fuel filter / water separator.
For 1000 series assemblies.
A redesigned filter with a center bail design.
Separates fuel from water with Aquabloc media.
Filter is 2 microns.

Turbine series fuel filter / water separator.
For 1000 series assemblies.
A redesigned filter with a center bail design.
Separates fuel from water with Aquabloc media.
Filter is 10 microns.

Turbine series fuel filter / water separator.
For 1000 series assemblies.
A redesigned filter with a center bail design.
Separates fuel from water with Aquabloc media.
Filter is 30 microns.

Turbine series fuel filter / water separator.
For 1000 series assemblies.
A redesigned filter with a center bail design.
Separates fuel from water with Aquabloc media.
Filter is 10 microns.

A replacement Turbine series filter element for Racor fuel/water separator units.
Features several improvements over previous models:
- A side-seam, center-bail design, which eliminates the metal "V-clip"
- Increased bail strength, by moving the bails to the top of the filter
- Improved capacity for dirt/soil/scum.
For 1000 series Racor fuel filter assemblies.
Includes a T-handled O-ring and lid seal kit.
Filter is 2 microns.

Includes gasket and O-ring. 2 micron. For secondary/final filtration. Brown.

Non-slip nylon belt with a 1/2" square drive. Fits spin-on filters up to 6" diameter.

Rated for 30 GPH. Gasoline only. 10 micron filter. Replaces filter on Racor 320R-RAC-02.

Replacement filter element. 30 micron. Fits the Racor 120A, 120R, 122R, and 140R. For diesel or gasoline. M18 X 1.5 center thread port connection.

Engineered to repel water and remove contaminates. For model 120A filter assemblies. Filter is 2 microns. Rated for 15 GPH.

Rated for 30 GPH. 10 micron filter. Fits the Racor 120A, 120R, 122R, and 140R.

Engineered to repel water and remove contaminates.
Used as a primary filter for 500 series turbine assemblies.
Rated for 60 gallons per hour. Filter is 30 microns.

Racor fuel filter / water separator turbine with three-stage filtration.
Provides maximum protection of diesel engine components.
Effectively removes contaminants from fuel.
Filters out water, silica, sand, dirt, rust and more.
See-through bowl.
2 micron element included.
Max flow rate: 90 GPH.
Port size: 5/8" ORB.
Replacement element: 2040N series.
 
Dimensions: 16.5"H X 5.96"W X 5.96"D.

Rugged corrosion-resistant steel construction. Wide studded band prevents crushed filters. Fits 2-13/16" to 3-5/32" diameter oil filters.

For 900/1000.
Coverts older models to meet the new ABS rules.
Part number: RK11734.

Kit includes:
- Clear bowl
- Replacement gasket
- 1/2" SAE plug.

Includes O-rings and bowl plug Use with model 500MA Weight: .5 lb

#8 MORB X #10 MJIC.

Surface-mounted audio/visual alarm. Buzzer and red light activates when water is detected. Does not have "mute alarm" option. Buzzer sounds until water is drained from fuel filter bowl.

T-handle vacuum gauge fitting. Size: 1/4" NPT threads to 9/16"-18 UNF. For use with Racor vacuum gauge. Part number: 11-1668. Weight: .25 lb.

For use with 900/1000 turbine series filters. Includes O-ring.

Plastic hand wrench for filter bowls. Removes all Racor metal and plastic spin-on bowls. Weight: 1.5 lbs.

For Racor 900 or 1000 fuel filter/water seperators.

Stainless steel and ceramic construction.
Durable plastic connector housing.
Metal pin tip extends into water collection bowl.
External pigtail harness with 18 AWG wires.

Kit includes all needed seals and O-rings for a rebuild of a Racor 500 fuel filter system.
Manufacturer's number: #RK15211.

For the Racor 500FG series.
Includes:
- Clear bowl
- Drain plug (1/2")
- Sensor screw cap
- Seals.

Stainless steel case, polycarbonate lens.
Helps to lengthen the life of filters.
Includes RK19669 pressure gauge and T-handle.
Replaces Racor RK11-1969 / RK 11-1669 / RK23284 gauges.
Used with 500 / 900 / 1000 turbine fuel filters.

For use with RK111938.

Plastic construction.
For 500FG or 1000FG Racor fuel filter systems.

Has a water probe port and plug.
For use with 900/1000 turbine series filters.
Includes O-ring.