Designed for the tough demands of the fishing industry. Equipped with a liquid-cooled 12-pole motor. Features a mechanical shaft seal and a threaded port. Uses 1-1/2" and 2" ports. Rated for 4000 GPH.

Provides high pumping capacity and reliability.
All-in-one pump and intelligent switch.
Designed to activate at 2-1/2" deep water.
Circuit will automatically cycle when needed.
1-1/8" discharge outlet.
12 volts DC.

Electronic water sensor and pump in one housing.
Provides high pumping capacity and reliability.
Circuit will automatically cycle when needed.
1" and 1-1/8" discharge outlets.
Rated for 2000 GPH.
24 volts DC.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/2" discharge outlet.
Model number: 14A.
3700 GPH.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
Compact, great for small spaces.
Cycles every 2.5 minutes.
Fully automatic, doesn't require float switch.
High efficiency, low amp motor
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
Model number: 27SA, round.
Three wire.
1100 GPH.
(Replaces RUL27S-3.)

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
Model number: 27DA.
1100 GPH.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
24 volts DC.
1-1/2" discharge outlet.
Model number: 16A.
3700 GPH.

Non-automatic; used with a panel and/or float switch.
Submersible and ignition protected.
High-efficiency, low-amp motor (1.6 amps at maximum flow).
Designed not to "burn out" when dry.
Stainless steel shaft.
Includes a back flow prevention device.
Model: 25DA.
Rated for 500 GPH.
3/4" port.
12 volts.

Automatic; no float switch needed.
Checks for water every two and a half minutes.
Runs for 1/2 second.
Consumes .2 amps per day.
Submersible and ignition protected.
High-efficiency, low-amp motor (1.6 amps at maximum flow).
Designed not to "burn out" when dry.
Stainless steel shaft.
Includes a back flow prevention device.
Model: 25SA.
Rated for 500 GPH.
3/4" port.
12 volts.

Reliable, rugged diaphragm pump. Portable, lightweight. All Delrin plastic construction. Self-priming. 12 foot delivery suction lift. Vertical handle orientation. Inlet / outlet diameter: 1".

Has some of the most advanced features in the industry. Removable motor cartridge for cleaning and replacement. Rated for 750 GPM. Equipped with easy-to-install Dura-Port discharge ports. 3/4" fitting. Dimensions: 2.75" X 4.4".

Place pump end in low point of bilge and powerful self-priming action gives full suction on first stroke. Quick, easy pump out of bilges and other flooded areas Compact, easy to stow, only 17" (430mm) long Includes 5 ft. length of 1/2" discharge hose Weight: 1.7 lb

Designed for automatic operation with an Ultima switch. Rated for 1250 GPH. Equipped with easy-to-install Dura-Port discharge ports. 1-1/8" fitting.

Designed for the tough demands of the fishing industry. Equipped with a liquid-cooled 12-pole motor. Features a mechanical shaft seal and a threaded port. Uses 1-1/8" ports. Rated for 1600 GPH.

Designed for automatic operation with an Ultima switch.
Rated for 1000 GPH.
Equipped with easy-to-install Dura-Port discharge ports.
3/4" fitting.

Provides high pumping capacity and reliability.
All-in-one pump and intelligent switch.
Designed to activate at 2-1/2" deep water.
Circuit will automatically cycle when needed.
1" and 1-1/8" discharge outlets.
12 volts DC.

Reliable, rugged diaphragm pump. Portable, lightweight. All Delrin plastic construction. Self-priming. 12 foot delivery suction lift. Vertical handle orientation. Inlet / outlet diameter: 1-1/2".

Designed to remove water from basements, garages, stairwells, utility rooms, back yards, sumps, pools, pool covers, boats and more.
Fully-automatic version uses standard 110 volt AC current
8' cord.
1800 GPH.

A lighter, compact pump for smaller vessels.
Tough plastic body with integral strainer.
Quick-release inlet strainer allows for quick cleaning.

12 volt DC.
3/4" hose connections.
Output: up to 23 liters per minute.

Includes a Rule 35A non-mercury float switch.

Provides ultimate pumping performance and fully automatic operation.
Designed to help keep your boat clear of nuisance water.
Equipped with a powerful 800 GPH high-capacity pump.
Tough impact-resistant sealed polycarbonate lid.
3/4" discharge port.
Simple to install.

A multi-purpose hand pump kit. Brass and neoprene construction. Corrosion resistant. Great for draining or filling engine and gearbox oil. Rated for up to 1-1/2 GPM output. Includes: - Pump - Two 1/2" hoses, 3 feet length - Two dipstick probes, 1/4" and 5/16" - Connector and adapter for 1/2" hose. Not designed for pumping flammable liquids.

Designed to remove water from basements, garages, stairwells, utility rooms, back yards, sumps, pools, pool covers, boats and more.
Fully-automatic version uses standard 110 volt AC current
24' cord.
1800 GPH.

Rated for 1000 GPH. For showers, dishwashers, galley sinks, and more. Automatic action for draining from sump tank. Has a tight-fitting lid to prevent spashes and odors. Dimensions: 11.42" X 8.26" X 5.7".

Dash alarm for Rule bilge pump.
12 volts.
Does not include bilge pump switch. 

Non-automatic.
Rated for 900 gallons per minute.
Designed to bring pumping power to tight spaces.
Equipped with a backflow prevention valve.
For horizontal or vertical mounting.
12 volt DC.

Automatic.
Rated for 900 gallons per minute.
Designed to bring pumping power to tight spaces.
Equipped with a backflow prevention valve.
For horizontal or vertical mounting.
12 volt DC.

Included check valve prevents backflow.
Threaded discharge for easy installation and maintenance.
Connectors: 3/4" and 1".
Rated for 800 GPH.
May be operated by a separate panel switch or a float switch.
12 volt DC.

Automatic bilge pump.
1-1/8" discharge outlet.
Senses when bilge water reaches 2-3/4".
12 volt DC.
Rated for 1100 GPH.

Designed for the tough demands of the fishing industry. Equipped with a liquid-cooled 12-pole motor. Features a mechanical shaft seal and a threaded port. Uses 1-1/8" and 1-1/4" ports. Rated for 2200 GPH.

An optimized impeller gives great flow at low amperage. 
A built-in thermal cut-off protects pump and vessel. 
Backflow preventer helps keep bilges dryer and cleaner. 
3/4" discharge outlet. 
Includes both straight and 90° port attachments. 
12 volts DC. 
Model number: 24DA. 
360 GPH.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/8" discharge outlet.
Model number: 02.
1500 GPH.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/8" discharge outlet.
Model number: 04.
1500 GPH.
Includes a five-year warranty from Xylem.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/8" discharge outlet.
Model number: 09.
2000 GPH.
Includes a five-year warranty from Xylem.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
24 volts DC.
1-1/8" discharge outlet.
Model number: 12.
2000 GPH.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/8" discharge outlet.
Model number: 10.
2000 GPH.