#6 MSAE to #5 FSAE.

Right Hand VTM42 pump

Hydro-Slave hanging pot hauler. Equipped with a Char-Lynn 1003 5.9 CID motor. Complete with a cast aluminum housing. - Stainless steel discs. - Stainless steel center hub and splitter - Aluminum fairlead rollers with stainless steel pins. Provides 380 lbs. line pull, 35 RPM per gallon.

Rated for 100 GPM. 100 mesh. Dimensions: 4" X 3".

Hydraulic motor must run at 1750 RPM, 8 GPM at 1500 PSI to drive water pump to 5 GPM at 2000 PSI.

Hydraulic hose. Nitrile blend and neoprene construction. For high pressure lines, up to 2250 psi. Color: Black. Diameter: 3/4". Sold by the foot.

Hydraulic hose. Nitrile blend and neoprene construction. For high pressure lines, up to 2750 psi. Color: Black. Size: 5/8". Sold by the foot.

Hydraulic hose. Nitrile blend and neoprene construction. For high pressure lines, up to 2000 psi. Color: Black. Diameter: 1". Sold by the foot.

Hydro-Slave hanging pot hauler.
Equipped with a Char-Lynn 24 CID motor.
Complete with extra heavy anodized cast aluminum housing.
- Stainless steel discs.
- Cadmium-plated disc liners.
- Stainless steel center hub and splitter.
- Aluminum fairlead rollers with stainless steel shafts.

NOTE: Due to the size of this product, shipping via UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Hydraulic hose. Nitrile blend and neoprene construction. For high pressure lines, up to 4000 psi. Color: Black. Diameter: 3/8". Sold by the foot.

Hydraulic hose. Nitrile blend and neoprene construction. For high pressure lines, up to 5000 psi. Color: Black. Diameter: 1/4". Sold by the foot.

Hydraulic hose. Nitrile blend and neoprene construction. For high pressure lines, up to 3500 psi. Color: Black. Diameter: 1/2". Sold by the foot.

Open center. Non load reaction.

Thick shim. For 10" block.

Cadmium plated sheave liners. For use with 14" hauler.

Engine, pump, tank, filter: a self-contained unit.
Fully assembled and mounted with stainless steel fasteners.
Marine-grade aluminum base with aluminum handle.
5 GPM 4-stroke, 5.5 horsepower Honda gasoline engine.
Suitable for powering 10" hauler head assemblies.
Electric-start enabled.

NOTE: Engine on this power pack is shipped WITHOUT oil.  Fill engine with oil to proper lever before starting.

NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options. 

V20 hydraulic pump assembly.
Complete with steel bracket and 12 volt clutch.
2.59 CID, 13 GPM at 1500 RPM.
Right hand rotation.
Inlet: 1-1/4" NPT.
Outlet: 3/4" NPT.

Hydro-Slave hanging pot hauler. Equipped with a Char-Lynn 18.7 CID motor. Complete with extra heavy anodized cast aluminum housing. - Stainless steel discs. - Cadmium-plated disc liners. - Stainless steel center hub and splitter. - Aluminum fairlead rollers with stainless steel shafts. Provides 1050 lbs. line pull, 12 RPM per gallon.

Plastic construction. For use with 12" or 14" hauler.

4 GPM controlled flow. 1000 PSI relief. 7/8" 13 tooth shaft. SAE-B 2-bolt mount. Left hand rotation.

4.88 CID.
Loadsense / pressure compensated.
Right hand rotation.
7/8" - 13T shaft.
2 BLT "B" flange.
Rear port.
Solo.

Popular with trollers and gillnetters.
Delivers 7.5 GPM at 1500 RPM.
Imported with manifold.
Right hand rotation.
1.18 CID.

For closed center systems only. Non load reaction.

Hydraulic steering control unit.
Closed center.
Non-load sense.
NBR seals.
Connection: 3/4" - 16 UNF.
Maximum input pressure: 175 bar (2500 PSI).
Maximum continuous backpressure: 25 bar (360 PSI).
VFU: 100.
Flow rating: 10 liters / minute.
Displacement: 5.9 cubic inches.

High-pressure through-deck (bulkhull) fitting.
Stainless steel construction.
Rated for 3000 psi, for use with hydraulic systems.
Two female NPT ports: 1-1/4".
Overall dimensions: 5.5" X 3".

Zinc-plated steel.
1/4" NBSPT to 3/8" MJIC.

4 GPM flow rate.
1000 PSI setting.
Right hand rotation.
2 bolt "A" flange mount.
3/4" - 11 tooth splined shaft.

Open center. 12 GPM rated flow. 5000 PSI maximum. Spring to center with fourth position hold. Fourth position allows for anchor winch free wheel.

Bracket 180 degrees for internal mount.
Direct drive 50 cubic inches.
Radial piston cam-lobe motor.
Highly efficient with very low noise.
Approximately 1000 lb. torque at 1450 PSI.
150 maximum RPM.
400 maximum RPM (freewheeling).
Compatible with open or closed loop hydraulic systems.
Equipped with Rexroth drum adapter flange.

NOTE: Due to the size of this product, shipping via UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Standard end plate for SL3 valve

26.4 Max GPM.
Ports:
Pressure: #12 SAE ORB
Return: #12 SAE ORB
Load Sense: #4 SAE ORB
Pressure relief to 5000 PSI.

1.16 CID. 3/4" keyed shaft. Right hand rotation. Rear ported. Bleed down compensator. Load sensed / pressure compensated. SAE-A 2-bolt flange mount.

For use with a Hydrocontrol D4 sectional valve.
Four bolts (with nuts and washers) per kit.

Displacement: 7.3 CID.
Shaft: 1" straight keyed shaft.
Flange: 2 bolt SAE-A.
Ports: 1/2" NPT.

Eaton Char-Lynn 104 2000 series hydraulic motor. Displacement: 11.9 CID. Shaft: 1-1/4" tapered shaft. 2-Bolt SAE-A mounting flange. #10 SAE ORB ports.