3/8" compression X 1/4" MNPT X 3/8" compression tee.
Three per package.

Package of 10 quad rings. Part number HS6038.

Rubber construction. O-rings. Thickness: .210". 20 per package.

For pivot mount cylinders. No adapters are required.

-5 ORB to 3/8". Tee adapters for hydraulic steering. Two per pack.

Tee fitting.  
#5MORB X 3/8" compression X 3/8" compression.
Two per package.

-5 ORB to 3/8". Tee adapters for hydraulic steering. Two per pack.

1/4" FNPT X #5MORB adapter.
These fittings are made of corrosion resistant stainless steel.
Three per package.

45˚ adapter elbow.
3/8" compression X #5MORB.
2 per package.

SeaStar Pro Kevlar reinforced steering hose.  
Includes two hoses - can be used with all
SeaStar systems, except BayStar, Capilano
and 3-line inboard systems.
Factory swaged fittings.
Length: 18'

Fill and valve assembly for hynautic reservoirs. Manufacturer number: HP6122. Weight: .10 lb.

SeaStar aluminum inboard cylinder rod end ball joint.
Stainless steel.
1/2" x 20FNF thread, 1/2" hole.

SeaStar cylinder specific large rod end ball joint.
Stainless steel.
3/4" x 16FNF thread, 3/4" hole.

SeaStar/Capilano brass cylinder rod end ball joint.
Stainless steel.
5/8" x 18FNF thread, 5/8" hole.

Two hoses, equal length. Factory swaged fittings. Kevlar-reinforced hose. For use with steering systems. Length: 36 feet.

SeaStar standard outboard steering hose kit.
Includes two hoses.
For all SeaStar systems, except SeaStar PRO,
BayStar, Capilano and 3-line inboard systems.
Factory swaged fittings.
Length: 14'

SeaStar standard outboard steering hose kit.
Includes two hoses.
For all SeaStar systems, except SeaStar PRO,
BayStar, Capilano and 3-line inboard systems.
Factory swaged fittings.
Length: 16'

SeaStar standard outboard steering hose kit.
Includes two hoses.
For all SeaStar systems, except SeaStar PRO,
BayStar, Capilano and 3-line inboard systems.
Factory swaged fittings.
Length: 18'

Allows for the periodic required realignment of two outboard
motors or rudders that are linked together with a hydraulic
tie bar as opposed to a solid link or a mechanical tie bar.

Vented male helm pump plug.
Must be used with helm pump on all single
steering station systems.
Must also be used on uppermost helm pump on
multi-steering station systems.
Ergonomic design to assist with the
installation and removal resulting in less
chance of over-tightening leading to damage.

Non-vented male helm pump plug.
Must be used on all helm pumps other than uppermost helm
pump on multi-steering station systems.
Ergonomic design to assist with the installation and removal
resulting  in less chance of over-tightening leading to
damage.

This kit makes bleeding and purging your SeaStar hydraulic steering system much easier.
Seastar suggests: first, pre-fill your helm, attach the filler kit with a quart of SeaStar fluid (HA5430H), puncture the bottom end of the bottle with the included pushpin, and begin the bleeding process.

This kit is designed to retrofit a new
SeaStar helm into a larger dash cut out (4.5")
or reduce helm protrusion from the dash by
the thickness of the dash.
Not for use with Baystar helm pumps.

Bleed tee (TM Cylinders).
3/4" UNF 45˚ flare (1/2" tube) X 3/8" NPT X bleed nipple.
Two per package.

Vertical bleed tee.
3/8" compression X 3/8" NPT X bleed nipple.
Two per package.

3/8” compression X 1/4" MNPT 90˚ elbow.
Three per package.

Horizontal bleed tee.
3/8" compression X 1/4" NPT X bleed nipple.
Two per package.

3/8" compression tube nut.  
For use with 3/8" nylon and/or 3/8" copper tubing.
Six per package.

3/8" compression tee.
Three per package.

Bleed nipple.
Includes O-ring.
For use with front mount cylinders only.
Two per package.