Designed for small spaces and the marine environment. Easily connects with other busbars and fuseholders. High temp plastic and clear polycarbonate construction. 4x 6mm (1/4") studs. 10 x 4mm (5/32") terminals. 200A maximum per bar. Dimensions: 3.9" x 1.9" x 2.0".

Ancor primary wire, 16 AWG. Manufactured from tinned copper for corrosion prevention. Insulated with a flexible proprietary vinyl coating. Resists cold, salt water, UV rays, and many petrochemicals. Color: Dark Blue. Length: 500 feet.

Replacement inlet interior for Marinco standard non-metallic inlets manufactured prior to 1/1/91.  
30A 125V.

Stainless steel construction, with lift lid. Fits 4700CR, 5262CRR, and 5739CR duplex receptacles.

Use with 6361CRN or 6365CRN. Can be used on both male and female ends.

For use with threaded 50 amp systems.

AFI 1.5 motor with 80 degree sweep. For a 22" Deluxe arm/blade combination or a 20" Premier arm/blade combination. Fully sealed, powder-coated aluminum base and housing. Chrome-plated solid brass drive nut. Brass and stainless steel drive shaft. Factory pre-set sweep angles of 80 or 110 degrees, easily adjusted to 45 or 60 degrees. Sealed 6" wire leads, 16 AWG; for 12 volt systems. Dimensions: 7-3/4" X 4" X 2-3/4"; 2" shaft.

AFI 1.5 motor with 80 degree sweep. Designed to power a 22" Deluxe arm/blade combination or a 20" Premier arm/blade combination. Fully sealed, powder-coated aluminum base and housing. Chrome-plated solid brass drive nut. Brass and stainless steel drive shaft. Factory pre-set sweep angles of 80 or 110 degrees, easily adjusted to 45 or 60 degrees. Sealed 6" wire leads, 16 AWG; for 12 volt systems. Dimensions: 7-3/4" X 4" X 2-3/4"; 1" shaft

Heat shrink tubing - 1/4" X 48". Cross linked polyolefin tubing is much stronger than PVC. Heat activated adhesive lining provides impervious seals. Protects from saltwater, oil, acid, sunlight, and strain. Able to shrink down to 1/3 of original size. Dimensions: 1/4" X 48". Color: Black. Weight: .15 lb.

125 volt, 50 amp female to 125 volt, 15 amp male. Covers and sealing collars for wet locations Sealing collar system joins adapter to cord set. Positive, mechanical connection Provides the maximum in moisture protection.

Connects dockside receptacle to boatside inlet. Features a sealing collar. 30 amp, 125 volt female to 50 amp, 125 volt male.

Cover for 10-1/2" x 7-1/2" Provides electrical insulation for exposed panel backs Provides protection for panel backs protruding into locker. Meets ABYC requirements for panels with combined AC and DC Lightweight material is easily drilled for wire enter/exit

Provides electrical insulation for panel backs.
Lightweight material is easily drilled for wires.
Meets ABYC requirements for panels with AC and DC.
Dimensions: 5-1/4" X 7-1/2" X 3".

Ancor primary wire, 14 AWG. Manufactured from tinned copper for corrosion prevention. Insulated with a flexible proprietary vinyl coating. Resists cold, salt water, UV rays, and many petrochemicals. Color: White. Length: 18 feet. Weight: .47 lb. per spool.

Designed for small spaces and the marine environment. Easily connects with other busbars and fuseholders. High temp plastic and clear polycarbonate construction. 4x 6mm (1/4") studs. 10 x 4mm (5/32") terminals. 200A maximum per bar. Dimensions: 3.9" x 1.9" x 2.0".

Pair of red and black caps For batteries with marine adapter terminals. Cable Size: 1/0, 2/0

Pair of Red/Black caps Top rotates 360 degrees to allow cable entry from any angle For batteries with integral marine wing nut posts For all cable sizes Weight: .25 lb

Ancor primary wire, 16 AWG. Manufactured from tinned copper for corrosion prevention. Insulated with a flexible proprietary vinyl coating. Resists cold, salt water, UV rays, and many petrochemicals. Color: Green. Length: 25 feet.

Ideal for non-conduit situations in a marine environment.
Durable, high-impact housing, will not break.
Compact, rugged design.
Feed under carpet, behind walls or through panels.
Length: 15 feet.