For use with 82605 series pump.
Rated for 70 PSI.

Used in retrofits of crank driven pumps. For Volvo, Indmar, and Marine Power engines.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
Cycles every 2.5 minutes.
Fully automatic, doesn't require float switch.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/2" discharge outlet.
Model number: 55S.
3700 GPH.

For Jabsco electromagnetic clutch. 12 volts.

Rated for 60 PSI. For 32605 series pumps.

For Jabsco pumps. Three per bag.

Replacement inner seal for Jabsco pumps. For 777 series pumps.

Jabsco pump head, model 18610-0001 1/2" NPT ports with garden hose adapters Weight: 2.75 lbs

Steel. Three per bag.

Check valve for Jabsco pump.

A variable speed drive system. Adds pressure-sensor control to everyday pumps. Senses real-time changes in pressure. Provides smooth and pulsation-free performance. Works on most water presure systems. 12 volts.

"Snap-In" straight port kit.
1/2" hose barb connectors.
Two per package.

Rated for 25 PSI. For 31200 series pumps.

Use for diesel fuel transfer, liquid transfer jobs, dockside pumping, dewatering or circulation, engine oil changing Fitted with oil resistant elastomers Self-priming, may be mounted above the waterline Heavy-duty ball bearings, thermal overload protection Continuous duty motor provides quiet operation & smooth flow Runs dry without harm to pump Includes plug-in ports for easy installation, two garden hose ports and two 3/4" hose barb ports Includes a 3/4" inlet strainer Weight: 6 lbs

Self-priming pump with run-dry protection. Triple-sealed motor to prevent corrosion. Four-bladed chopper reduces clogging. Flow rate: 12 GPM. Self primes up to 4 feet of vertical lift. Ports: 1-1/2" and 1". 24 volts DC, 8 amp draw.

Jabsco pressure switch. Rated for 25 PSI.

Cam screws for Jabsco pumps. Pack of three.

Bronze construction. Tolerates hard or soft solids. Pumps in either direction, will not airlock. 1-1/2" ports. Rated for 44.5 gallons per minute.

Jabsco pressure switch. 50 psi. For use with 31700.

Black plastic construction.

For 36950 diaphragm pump. Includes diaphragm, valve set, and dampeners.

Coated wood construction. Includes hinge components. Fits 29090, 37045, 37045, 37010 and other toilets.

For Jabsco pumps, 6050 series. Three per bag.

Bronze construction. Nitrile impeller. Lip seal, stainless steel shaft. 1/2" ports, horizontal orientation.

Use for engine cooling, wash down, circulation, and general purposes on-board or dockside Self-priming with ability to operate in either direction at variable speeds Removable end cover for easy impeller service 11.3 GPM - 1/2" NIPT - 5/8" diameter shaft Weight: 4.51 lbs

Multiple flow control settings. Can work with both fresh and salt water. Designed for use with washdown pumps.

Replacement bearing for Jabsco pumps.

Electromagnetic clutch pumps equipped with a powerful electric clutch for convenient remote operation 12 volt model Capable of operating through a wide range of speeds and in either rotational direction 1B Pulley Belt Grooves - 1" NIPT - 26 GPM Weight: 14.75 lbs

Three per bag.

Strains debris and particles from bilge pump line. Clear plastic housing for easy inspection. Easy to disassemble and clean. 16 mesh stainless steel screen. 3/4" hose barb ports.

High impact plastic construction. Will not rust, corrode or discolor. Designed for use with Rule pumps. Size: 3/4".

Keeps debris from entering your pump. Plug-in Quad port. Threaded bowl makes cleaning easy. 40 mesh, stainless steel screen. 3/4" hose barb.

Cam screws for Jabsco pumps. Pack of three.