For MRB75 / 80.

This kit is designed to mount the helm
at a 20 degree angle to the mounting surface.
For raised or recessed mounts, four possible
mounting configurations are available.
Horizontal recessed mount requires HA5408 drain kit.
Not for use with BayStar helm pumps.

Designed to fit all brands of hydraulic trim tabs. Includes: - 12 volt motor - InstaTrim oil circulation pump (400 psi) - Solenoid valves - 18" wire harness with color coded wires - Biodegradable transmission oil and funnel - All fittings needed for installation.

Required for converting a SyTen steering cylinder to a current SeaStar Steering cylinder.

For Teleflex installation purposes. Includes O-rings.

Replacement shaft seal kit. Fits HRP-60 helms.

Replacement shaft seal kit. Fits HRP30-2 helms.

Replacement shaft seal kit. Fits HRP-38 helms.

Replacement shaft seal kit. Fits HRP-23 helms.

18" SeaStar cylinder hose kit.
Used to connect 3/8" diameter copper tubing to SeaStar steering cylinders.
Adapters and compression nuts included.

Fitting kit for 2nd station/autopilot to inboard or sterndrive applications.
This kit is used with systems plumbed with 3/8" diameter nylon or copper tube only.

Fitting kit to add a 2nd station or autopilot to an outboard steering system.
To be used when the system has been plumbed with SeaStar outboard steering hose only.
Includes non-vented fill plug for lower station helm.

3/8” compression X 1/4" MNPT straight adapter fitting.
Three per package. 

3/8" compression union.
Three per pack.

Elbow. 1/4" X 3/8". Three per package.

1/4” MNPT X 3/8” compression X 3/8" compression tee.
Three per package.

3/8" X 3/8" X 3/8". Three per package.

3/8" compression X 1/4" MNPT X 3/8" compression tee.
Three per package.

Female #6 SAE 45° swivel X 5/16" ID hose.
Brass construction.                      
Field attachable.                        
Fits MSH-5 hose.  

Model 7003.
Includes O-rings and a front seal.

Vertical bleed tee.
#5MORB X 3/8" compression x bleed nipple.  
Two per package.

Horizontal bleed tee.
#5MORB X 3/8” compression x bleed nipple.
Two per package.

90˚ elbow.
#5MORB X 3/8” compression.  
Two per package. 

Straight adapter.  
3/8" compression X #5MORB.
Two per package.

Replacement shaft seal kit. Fits H-600 series helms.

3/8" OD semi-rigid black nylon tubing.
For Hynautic steering control systems.
High tensile strength and excellent coupling
retention in high pressure, temperature and
vibration environments.
Sold by the foot.

Replacement ball joint. Includes washer and nut.

Replacement ball joint. Includes washer and nut.

SeaStar Pro Kevlar reinforced steering hose.  
Includes two hoses - can be used with all
SeaStar systems, except BayStar, Capilano
and 3-line inboard systems.
Factory swaged fittings.
Length: 10'

SeaStar Pro Kevlar reinforced steering hose.  
Includes two hoses - can be used with all
SeaStar systems, except BayStar, Capilano
and 3-line inboard systems.
Factory swaged fittings.
Length: 12'

SeaStar Pro Kevlar reinforced steering hose.  
Includes two hoses - can be used with all
SeaStar systems, except BayStar, Capilano
and 3-line inboard systems.
Factory swaged fittings.
Length: 16'

Replacement seals. Fits MRB-100A actuator.

This kit is used to service many BayStar and SeaStar helms.
Includes:
- Quad ring seal
- Woodruff key
- 5/8" nut
- A top plate
- 3 screws
- Detailed instructions for servicing a SeaStar helm.

For hydraulic control systems. Diameter: 1/4".

Rear-mounted gauge. Displays 0 - 60 PSI.

Fits SeaStar front mount outboard cylinders.