45˚ adapter elbow.
3/8" compression X #5MORB.
2 per package.

For transferring hydraulic fluid. Used with Marol helm pumps.

SeaStar Pro Kevlar reinforced steering hose.  
Includes two hoses - can be used with all
SeaStar systems, except BayStar, Capilano
and 3-line inboard systems.
Factory swaged fittings.
Length: 18'

Saltwater and corrosion resistant. Rated for 1000 psi working pressure. Used for hydraulic steering systems. Fiber-reinforced nylon tube with a polyurethane cover. Color: Black. Diameter: 3/8".

Saltwater and corrosion resistant. Rated for 1000 psi working pressure. Used for hydraulic steering systems. Fiber-reinforced nylon tube with a polyurethane cover. Color: Black. Diameter: 5/16".

Fill and valve assembly for hynautic reservoirs. Manufacturer number: HP6122. Weight: .10 lb.

SeaStar aluminum inboard cylinder rod end ball joint.
Stainless steel.
1/2" x 20FNF thread, 1/2" hole.

SeaStar cylinder specific large rod end ball joint.
Stainless steel.
3/4" x 16FNF thread, 3/4" hole.

SeaStar/Capilano brass cylinder rod end ball joint.
Stainless steel.
5/8" x 18FNF thread, 5/8" hole.

#5 MS HS to #6 3/8" tube
Brass construction.

Seal and O-ring kit for SeaStar Hynautic K-18 thru K-20
cylinders.

Plastic hose collar For use with InstaTrim boat leveler systems. Weight: .04 lb.

Two hoses, equal length. Factory swaged fittings. Kevlar-reinforced hose. For use with steering systems. Length: 36 feet.

Model MRB-80A. Volume: 24.1 cubic inches. Torque: 19126 inch pounds.

SeaStar standard outboard steering hose kit.
Includes two hoses.
For all SeaStar systems, except SeaStar PRO,
BayStar, Capilano and 3-line inboard systems.
Factory swaged fittings.
Length: 14'

SeaStar standard outboard steering hose kit.
Includes two hoses.
For all SeaStar systems, except SeaStar PRO,
BayStar, Capilano and 3-line inboard systems.
Factory swaged fittings.
Length: 16'

SeaStar standard outboard steering hose kit.
Includes two hoses.
For all SeaStar systems, except SeaStar PRO,
BayStar, Capilano and 3-line inboard systems.
Factory swaged fittings.
Length: 18'

For pivot mount cylinders. No adapters are required.

Model MRB-63A. Volume: 9.4 cubic inches. Torque: 7572 inch pounds.

#6 MS HS to #6 F SAE tube.
Brass construction.

#5 MS HS to #6 F SAE tube.
Brass construction.

Seal kits for SeaStar HC5801, HC5801-2,
HC5802, HC5803, HC5803-2, and HC5804
power steering cylinders.

Seal kit for SeaStar HC5801, HC5801-2,
HC5803, HC5803-2 power steering cylinders.

Built from strong, fiberglass-reinforced nylon. Has two expanding seals and O-ring for stopping leaks. Designed to retract when not in use for safety.

Trim Tab bracket. Swivel-style for mounting to boat at any angle. Fully adjustable. Equipped with pins that will shear in case of impact. Weight: .14 lb.

12 volt solenoid for Trim Tab systems. Custom design is epoxy sealed for water resistance. These solenoids lock the tabs in any postion. Barb-type hose fittings for a secure connection. For use with InstaTrim boat leveler systems. Weight: .36 lb.

Bleed fitting for use with Marol MRB rotary actuators.

Nylon/PVC hydraulic hose.
Rated to 2000 pounds burst pressure.

Sold by the foot, please order accordingly. 

Cylinder pin. For repairing Trim Tab cylinders. Weight: .01 lb.

Allows for the periodic required realignment of two outboard
motors or rudders that are linked together with a hydraulic
tie bar as opposed to a solid link or a mechanical tie bar.

Vented male helm pump plug.
Must be used with helm pump on all single
steering station systems.
Must also be used on uppermost helm pump on
multi-steering station systems.
Ergonomic design to assist with the
installation and removal resulting in less
chance of over-tightening leading to damage.

Non-vented male helm pump plug.
Must be used on all helm pumps other than uppermost helm
pump on multi-steering station systems.
Ergonomic design to assist with the installation and removal
resulting  in less chance of over-tightening leading to
damage.

This kit makes bleeding and purging your SeaStar hydraulic steering system much easier.
Seastar suggests: first, pre-fill your helm, attach the filler kit with a quart of SeaStar fluid (HA5430H), puncture the bottom end of the bottle with the included pushpin, and begin the bleeding process.

This kit is designed to retrofit a new
SeaStar helm into a larger dash cut out (4.5")
or reduce helm protrusion from the dash by
the thickness of the dash.
Not for use with Baystar helm pumps.

Bleed tee (TM Cylinders).
3/4" UNF 45˚ flare (1/2" tube) X 3/8" NPT X bleed nipple.
Two per package.

Vertical bleed tee.
3/8" compression X 3/8" NPT X bleed nipple.
Two per package.