Direct replacement for your twister or rotate mounting bracket 180 degrees for internal mount.
Direct drive 63 cubic inches.
Radial piston cam-lobe motor.
Highly efficient with very low noise.
Approximately 1230 lb. torque at 1450 PSI
130 maximum RPM 400 maximum RPM freewheeling.
Compatible with open or closed loop hydraulic systems.
Standard 6 bolt flange with pilot. Direct twister replacement.

NOTE: Due to the size of this product, shipping via UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Hydraulic quick-connect fitting.
#4.
Size: 1/4".
Rated for 0 - 3000 PSI.

Plated steel. #6 female JIC to #8 male JIC.

Replacement shaft for motor. 14 teeth.

Union. 
Stainless steel. 
#12 compression fitting to #12 compression fitting.

Stainless steel. 
#10 compression fitting to #10 male JIC

Stamped stainless steel discs For 10" hauling block.

Union. 
Stainless steel. 
#8 compression fitting to #8 compression fitting. 

Stainless steel hub For 10" hauling block.

For use with a Hydrocontrol D4 sectional valve.
Four bolts (with nuts and washers) per kit.

For use with a Hydrocontrol D4 sectional valve.
Four bolts (with nuts and washers) per kit.

Stainless steel splitter. For 10" haulers.

Union. 
Stainless steel. 
#10 compression fitting to #10 compression fitting. 

Open center. 25 GPM. 5000 PSI maximum. Spring to center with fourth position float. Fourth position allows for anchor winch freewheel.

Forged stainless steel.
For 12" hauler block.

Hydraulic steering control unit.
Closed center, load sensing.
NBR seals.
Connection: 3/4" - 16 UNF.
Maximum input pressure: 175 bar (2500 PSI).
Maximum continuous backpressure: 25 bar (360 PSI).
VFU: 80.
Flow rating: 8 liters / minute.
Displacement: 3.0 cubic inches.

Hydraulic steering control unit
Closed center
Load sensing.
NBR seals.
Connection: 3/4" - 16 UNF.
Maximum input pressure: 175 bar (2500 PSI).
Maximum continuous backpressure: 25 bar (360 PSI).
VFU: 100.
Flow rating: 10 liters / minute.
Displacement: 5.9 cubic inches.

Engine, pump, tank, filter: a self-contained unit.
Fully assembled and mounted with stainless steel fasteners.
Marine-grade aluminum base with aluminum handle.
11 GPM 4-stroke, 13 horsepower Honda gasoline engine.
Suitable for powering 12" hauler head assemblies.
Electric-start enabled.

NOTE: Engine on this power pack is shipped WITHOUT oil.
Fill engine with oil to proper lever before starting.

NOTE: Due to the size of this product, shipping via UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Needed for electrically actuated EX38 valves.
12 volt DC.
With # SAE ORB "Y" port.

Walvoil EX38 full flow sharing sectional valve. 
- Pressure-compensated flow control work sections 
- Sectional valve (1-10 sections) 
- Load sensing 
- Full flow pressure relief 
For use with mechanical, hydraulic, pneumatic and proportional electro-hydraulic controls. 
Manually actuated, spring to center spool. 
16 GPM. 
#10 SAE ORB Work ports 

Pressure compensated flow controlled sections.
Load sense configuration, adjustable pressure relief.
1 spring work section / 2 friction work sections.
Available in 16 GPM or 22 GPM work sections.

Gear motor assembly.
Series 26.
Bi-directional.
Straight shaft, 5/8".
Mounts with 2-bolt "A" SAE flange series 82-2.
1.24 displacement.

Open center / cylinder spool. 12 GPM rated flow. 3625 PSI maximum work pressure. P, A, and B ports #8 SAE O-ring. T port #10 SAE O-ring. Spring to neutral. Nickel plated spool. 2 banks.

NBR seals.
Loadsense.
Connection: 3/4" - 16 UNF.
Maximum input pressure: 175 bar (2500 PSI).
Maximum continuous backpressure: 25 bar (360 PSI).
VFU: 125.
Flow rating: 12.5 liters / minute.
Displacement: 7.3 cubic inches.

Open center / cylinder spool. 12 GPM rated flow. 3625 PSI maximum work pressure. P, A, and B ports #8 SAE O-ring. T port #10 SAE O-ring. Spring to neutral. Nickel plated spool.

Direct replacement for your twister or rotate mounting bracket 180 degrees for internal mount.
Direct drive 50 cubic inches.
Radial piston cam-lobe motor.
Highly efficient with very low noise.
Approximately 1000 lb. torque at 1450 PSI.
150 maximum RPM.
400 maximum RPM (freewheeling).
Compatible with open or closed loop hydraulic systems.
Standard 6 bolt flange with pilot.
Direct twister replacement.

NOTE: Due to the size of this product, shipping via UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Rated for 4 GPM. Right hand.

Stainless steel, glycerine-filled case. 0 - 3000 PSI range. 1/4" NPT lower mount. 2-1/2" diameter.

Open center.
Power beyond.
Maximum input pressure: 175 bar (2500 PSI).
Maximum continuous backpressure: 25 bar (360 PSI).
4 - 8 gallons per minute.

Open center.
Power beyond.
Maximum input pressure: 175 bar (2500 PSI).
Maximum continuous backpressure: 25 bar (360 PSI).
4 - 8 gallons per minute.

For use with fairlead roller. Size: 3".

Rated for 15 GPM. 100 mesh. Dimensions: 1-1/2" X 1".

Stainless steel.
#16 MJIC to #20 MORB.

For use with a Hydrocontrol D16 sectional valve.
Four bolts (with nuts and washers) per kit.