Nitrile. 9 blades. Diameter: 2".

Brass construction.
1" X 2".

Combination displacement lift / siphon pump. Suitable for transferring diesel, oil, or water. Clear tubing. Not intended for PVC-attacking solvents.

Heavy-walled FDA-approved vinyl compound. Reinforced with polyester braid. Non-toxic, tasteless, odorless. Red tracer in clear PVC. Appropriate for: - Hot/cold pressurized water systems - Vent and drain lines - Bilge pump discharge. For temperature range: 25° F - 150° F. Rated for a burst pressure of 250 psi. Size: 1-1/4".

Kink resistant and flexible. Designed with an EPDM tube and cover. Wire-reinforced with two fabric plies. Resistant to toilet chemicals, odors, salt water and heat. Primarily used for toilet to holding tank connections. Works well as a holding tank pump-out hose. Diameter: 1".

Neoprene. 10 blades. Diameter: 1-9/16".

Nitrile. 10 blades. Diameter: 1-9/16".

Same pump used in Jabsco multi-engine oil change system Can change oil in a typical V-8 in minutes 3/8" NPT male threaded Dimensions: 7-1/8"L x 3-3/4"W

Operates by the rotary sliding vane principle Has vectra rotor and vanes that are designed to handle oil or diesel fuel transfer Pumps up to 5-1/2 GPM and transfers diesel fuel from a 55 gallon drum in 10 minutes Self-priming to 3 feet - Low amp draw Vane Puppies are equipped with a high torque motor with ball type shaft bearings Rated for continuous duty operation Bronze pump has ports with 1/2" internal pump thread 1" external hose barb Also supplied are port adaptors for 3/4" gallon hose thread. Weight: 6.4 lbs

Clear PVC with a black vinyl helix. Abrasion, saltwater, and chemical resistant, flexible. Often used for: - Bilge pump discharge - Potable water tanks fills - Drains for sinks, showers, livewells, or scuppers. This hose uses 147 right hand thread cuffs. Do not attach to thru hull fitting below the water line. Not for use with glycol-based antifreeze. Diameter: 1".

Heavy-duty for hot or cold water systems. Extra wall thickness increases kink resistance. FDA-approved virgin vinyl compound. Diameter: 1/2".

An auxiliary water pump. 1" inlet and outlet. 12 volt.

Media for tank sand filter.

Hayward filter clamp.

Hayward two-way isolation control valve.

Electromagnetic clutch pumps equipped with a powerful electric clutch for convenient remote operation 12 volt model Capable of operating through a wide range of speeds and in either rotational direction 1B Pulley Belt Grooves - 1" NIPT - 26 GPM Weight: 14.75 lbs

Pump type: F5B-9.
For Volvo, AQ131, AQ140A-170.
JP part number: 10-32621-2.
Volvo part number: 855517.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 1-3/4". Length: 12.5 feet.

Designed for engine intake, bilge discharge and other lines.
Reinforced with wire helix embedded in synthetic material. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 1-3/8". Length: 12.5 feet.

U-bolt style exhaust clamp. 
Secures exhaust tubing. 
Diameter: 8". 

Compatible with many inboard and outboard motors. Will not separate 2 cycle oil from gasoline. 21 micron filter.

Cam screws for Jabsco pumps. Pack of three.

For Yamaha systems. Separates water from fuel. Rated for 10 microns.

Nitrile. F7B. Diameter: 2.56". For Johnson pumps.

28 Micron filter element shaped into 66 pleats-more capacity Steel end caps on elements - Heavy duty spring Powder coated outside/Epoxy coated inside, corrosion protection U.S.A. made, meets OEM specs Do not use with diesel fuel, will not separate 2 cycle oil from gas Replaces: Mercury 35-60494A4 Suzuki 99105-2000 Yamaha ABA-SEPAR-AT-OR Not recommended for 4.3 Mercruiser engines with electric fuel pumps

Separates water from gasoline.
Rated for 21 microns.

Double-ply soft wall, no wire.
For straight connection in wet exhaust systems.
Okay for either gasoline or diesel engines.
Designed for coolant and heat resistance.
Color: Black with blue stripe.
Temperature range: 0° to 212° F.
Diameter: 1".
Length: 12.5 feet.

Torrid water heater replacement anode rod. Magnesium construction. Protects your water heater from rusting. For use with MV15, MV71, MH15, MH17. Size: 18". Weight: .76 lb.

Torrid water heater replacement anode rod. Magnesium construction. Protects your water heater from rusting. For use with MV6, MV10, MH6, MH10. Size: 12". Weight: .54 lb

Replacement glass for in-line fuel filter. Clear for easy inspection. Filter traps dirt and metallic particles.