Replacement glass for in-line fuel filter. Clear for easy inspection. Filter traps dirt and metallic particles.

Torrid water heater replacement anode rod. Magnesium construction. Protects your water heater from rusting. For use with MH30, MH40. Size: 24". Weight: 1 lb.

Replaces Jabsco 30648-1000 "standard format" clips. For Flojet and Jabsco pumps. Two per package.

Gray iron. Powder coated. Shank Y hose end: 3". Hose end diameter: 4". Overall length: 9-1/2". Weight: 7 lb.

Nitrile. F7B. 8 blades. Diameter: 2.56". For Johnson pumps.

Easily converts a gas grill from using small disposable bottles to a larger, refillable cylinder.
Fully assembled and leak tested.
Great for boats, camping, picnics, and more.
Equipped with a hand-wheel POL cylinder fitting on one end, and a high-pressure appliance valve fitting on the other.
Length: 6 feet.

Can deliver almost 7 GPM at open flow.
Equipped with pressure-cast bronze body.
Features a reusable O-ring type end cover seal.
1/2" internal pipe thread and 1" external hose barb.
Includes 2 port adapter.
12 volt DC.

Bilge pump for larger boats. Rated for 1500 gallons per minute. Uses 1-1/8" hose. Meets USCG/ABYC standards. Equipped with a quick-release strainer base. Weight: 3.1 lbs.

Cast bronze Cast hex for easier installation Curved 90 degrees Pipe Size: 3" Hose Size: 3" Overall Length: 10" Weight: 6.375 lbs

Engine Cooling Pump & General Purpose Pumping 3.7 GPM, 1/4" NIPT Port Connections. Pedestal mount, corrosion resistant bronze pumps: Use for engine cooling, washdown, circulation, & general purposes on-board or dockside. Bronze or stainless steel shaft installed with permanently lubricated ball bearings for long life & heavy-duty service. Self-priming with ability to operate in either direction at variable speeds. Capacity ranges from 3 GPM to 83 GPM with varied port configurations and sizes. Most models have replaceable cams/wearplates for extended product life. Removable end cover for easy impeller service. Standard impeller for these pump models is neoprene. (some have alternative oil resistant nitrile impellers available.)

Submersible bilge pump - 600 gallons per hour. Tough enough for any bilge. Built from impact resistant ABS. Stainless steel hardware and shaft. Strainer base is quick-release for easy cleaning. Hose: 3/4". Weight: .8 lb.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 1-1/4". Length: 12.5 feet.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 1-1/8". Length: 50 feet.

Culligan P5-D filter cartridge. A level 4 spun polypropylene filter. Typically installed on main water lines. Removes sediment, rust, dirt, sand, and silt. Designed to reduce chlorine flavor and odor. Does NOT remove fluoride. 5 micron rating. Dimensions: 9-3/4" X 2-1/2". Weight: .65 lb.

A flexible impeller pump. Vertically oriented ports. Mechanical face seal, double row ball bearings. Neoprene impeller. 1" NPT. Overall dimensions: 7" X 4-1/4" X 4".

Cam screws for Jabsco pumps. Pack of three.

For use with Beckson 118P Thirsty-Mate hand pump.
Diameter: 1-1/4".

Black smooth vinyl cover with a helix. Rated for full vacuum. Resistant to chemicals and saltwater. Primarily used for bilge pump and discharge purposes. Easily bent, OK for below waterline connections. Diameter: 5/8".

Plastic pump body. Designed to provide constant water pressure. 3/8" ports. Automatic flow from tank to faucet. 12 volt DC.

Replacement impeller, MC97.
2-1/4" diameter.
Kit includes: O-ring, gasket, lubricant.

Prevents damage to lines due to rubbing and chafing. Color: Blue. 4" filled. 6.5" flat.

High-pressure seal kit.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/2" discharge outlet.
Model number: 13A.
3700 GPH.
Includes a five-year warranty from Xylem.

Heavy-duty, cast zinc body. Insulated grip for spraying hot or cold water. Brass head insert for strength. Rust-resistant stainless steel spring. Self-adjusting packing for leak-proof seals.

8 blades. Dimensions: 2-1/2" X 2". Shaft diameter: 5/8".

All plastic. Self lubricating, self-priming and very easy to clean. Will not rust or corrode. Will not mar boat. Length: 24".

Culligan S1A-D filter cartridge. A level 2 pleated cellulose filter. Typically installed on main water lines. Removes sediment, rust, dirt, sand, and silt. Designed to reduce chlorine flavor and odor. Does NOT remove fluoride. 20 micron rating. Dimensions: 9-3/4" X 2-1/2". Weight: .65 lb.

Diameter: 5/16". 50 foot coil.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
Model number: 27DA.
1100 GPH.

Designed for washdown or for livewell tanks.
Heavy-duty construction.
Ideal for commercial or pleasure boats.
1-1/2" inlet, 1-1/2" discharge outlet.
Rated for 3700 GPH.
Must be mounted below waterline.
Operates at low pressure; not self-priming.
24 volts DC.

Gauge float assembly. For use with Moeller fuel tanks. Manufacturer number: 621001-10. Weight: .5 lb.

Jabsco 50900 Fish Box evacuation pump. A single-diaphragm, 5 GPM plastic-body pump. Perfect for emptying the fisbox after a day's fishing. This self-priming pump is designed to pass debris, such as bait residue, ice particles, fish scales, etc. OK to run dry and equipped with a 360º rotatable head. 12 volt.

Great for evacuating small boats. Keep it on hand for emergencies. 36" long hose.

Self-priming hand pump.
Great for evacuating small boats.
Stash one in your canoe, kayak or dinghy.
Comes complete with a removable hose.

For Jabsco pumps. Three per bag.

Clear PVC with a black vinyl helix. Abrasion, saltwater, and chemical resistant, flexible. Often used for: - Bilge pump discharge - Potable water tanks fills - Drains for sinks, showers, livewells, or scuppers. This hose uses 147 right hand thread cuffs. Do not attach to thru hull fitting below the water line. Not for use with glycol-based antifreeze. Diameter: 1-1/4".  NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.  Please contact Seattle Marine at 1-800-426-2783 for shipping options.