Automatic bilge pump.
3/4" discharge outlet.
Senses when bilge water rises and turns on.
12 volt DC.
Rated for 500 GPH.

Replacement for the Jabsco 17935-0001 and Johnson 09-819B impellers. Only impeller able to run dry for 15 minutes Globe impellers are made of Brandonite a high-strength, elastomeric material with self-lubricating compounds for run-dry protection and improved resistance to sand and dirt to help keep you going in the most difficult conditions.

Unites two lengths of hose. Stainless steel. Diameter: 5/8".

Cast bronze These valve bodies are offered to meet the needs of applications that require extra long, scoop or flush type thru-hulls Flange Diameter: 5-1/2" Pipe Size: 1-1/2" Weight: 6.375 lbs

Replacement for the Sherwood 10077 impeller. Only impeller able to run dry for 15 minutes Globe impellers are made of Brandonite a high-strength, elastomeric material with self-lubricating compounds for run-dry protection and improved resistance to sand and dirt to help keep you going in the most difficult conditions.

For sanitation system connections. Multi-purpose, smooth-walled hose. For bilge, drain, or potable water uses. Temperature range: -13° to 158° F. Diameter: 3/4".

Cast bronze construction. Diameter: 1-1/2".

Cast bronze construction. Diameter: 1-1/4".

Cast bronze construction. Diameter: 1".

Replacement for the Jabsco 6056-0001 Only impeller able to run dry for 15 minutes Globe impellers are made of Brandonite a high-strength, elastomeric material with self-lubricating compounds for run-dry protection and improved resistance to sand and dirt to help keep you going in the most difficult conditions.

Union for joining pipe.
Bronze.
1".

Comes with kit of tubes and hoses, reducing foot and adapter Use for bilges, sump tanks, transfer, or oil changing from engine crank case, stern drive or inboard. Tube to insert in dipstick hole for oil pump out. Tough marine plastic will not rust or corrode. No priming to start pump action. Red discharge tube, gray hand pump. Weight: .75 lb

High dirt-holding capacity maximizes utilization of activated carbon.
Highly effective at reducing unpleasant taste and odor.
5 micron rating.
2-3/4" X 10". 

Fits housing #4-6 10230.

Use for engine cooling, wash down, circulation, and general purposes on-board or dockside Self-priming with ability to operate in either direction at variable speeds Removable end cover for easy impeller service 11.3 GPM - 1/2" NIPT - 5/8" diameter shaft Weight: 4.51 lbs

Fire-retardant marine fuel hose.
Resists alcohol-enhanced gasoline.
High nitrile rubber construction.
Reinforced with two spirals of synthetic fabric.
Diameter: 1/4".
50 feet per box.

Fire-retardant marine fuel hose. Resists alcohol-enhanced gasolines. High nitrile rubber construction. Reinforced with two spirals of synthetic fabric. Diameter: 1/4". 250 feet per spool.

Cast bronze. Diameter: 3".

Only impeller able to run dry for 15 minutes Globe impellers are made of Brandonite a high-strength, elastomeric material with self-lubricating compounds for run-dry protection and improved resistance to sand and dirt to help keep you going in the most difficult conditions.

Fire-retardant marine fuel hose. Resists alcohol-enhanced gasolines. High nitrile rubber construction. Reinforced with two spirals of synthetic fabric. Diameter: 1/2". 250 feet per spool.

Black smooth vinyl cover with a helix. Rated for full vacuum. Resistant to chemicals and saltwater. Primarily used for bilge pump and discharge purposes. Easily bent, OK for below waterline connections. Diameter: 3/4".

Designed for automatic operation with an Ultima switch. Rated for 1250 GPH. Equipped with easy-to-install Dura-Port discharge ports. 1-1/8" fitting.

Gathers fuel level information. Connects to dash mounted gauge without a conversion capsule. Measure tank depth and make the swingarm the correct length. Internal components will not rust or corrode. Float rotates easily in 90° increments. For 6" to 12" deep tanks.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 5/8". Length: 12.5 feet.

For use in extreme temperature conditions. 
Inner tube is red heat-resistant silicone. 
Reinforced with nylon fiber. 
Cover is heat and weather-resistant silicone. 
ID: 1/2". 
Rated for 80 PSI.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 2-7/8". Length: 12.5 feet.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 1/2". Length: 12.5 feet.

King Nipple - Straight Standard Flow 1-1/4" NPT x 1-1/4" hose - Bronze Weight .60 lbs

iL500 Plus pump. Suitable for diesel, salt or fresh water. Rated for 500 gallons per hour. Includes: - Pump - Spray nozzle - 4 meter cable with battery clips - 4 meter lay-flat hose. 3/4" ports. 12 volts.

Double-ply soft wall, no wire.
For straight connection in wet exhaust systems.
Okay for either gasoline or diesel engines.
Designed for coolant and heat resistance.
Color: Black with blue stripe.
Temperature range: 0° to 212° F.
Diameter: 3-1/2".
Length: 12.5 feet.

Direct sight gauge. Gathers fuel level information with the float. Accurate gauge will fluctuate as the fuel "sloshes". Length: 17-3/4".

Use for engine cooling, wash down, circulation, and general purposes on-board or dockside Pedestal mount, corrosion resistant bronze pumps Self-priming and portable, very versatile Removable end cover allows easy impeller service Pump heads are built of bronze materials 62 GPM, 1-1/4" NIPT Port, 1" shaft, face seal, brass cam and impeller insert Weight: 12.6 lbs

Replacement for the Jabsco 18838-0001 impeller. Only impeller able to run dry for 15 minutes Globe impellers are made of Brandonite a high-strength, elastomeric material with self-lubricating compounds for run-dry protection and improved resistance to sand and dirt to help keep you going in the most difficult conditions.