Replacement pump only, does NOT include clutch. Has a connection for a vacuum switch accessory. Bronze construction. Mechanical seal, stainless steel shaft. 1-1/2" ports.

A centrifugal booster pump. Bronze construction. 1/2" inlet and outlet. 12 volt.

Provides pumping power at the push of a button. Has a connection for a vacuum switch accessory. Bronze construction. Mechanical seal, stainless steel shaft. 1-1/4" ports.

Tournament series, high-capacity pump.
Rated for 1600 gallons per hour.
Bronze base.
1" ports.
12 volts.

For quick, easy and clean oil changes.
Includes dipstick probe and a female garden hose connector.
Reversible flow.
12 volt model with 8' cord and alligator clips.

Solid brass piston rod for strength & durability. Easily disassembled for cleaning. 1-1/2" barrel means quick pumpouts. 5 year warranty. Includes 24" of 1-1/8" black bilge flex hose.

Pump with oil resistant nitrile impeller Bronze body - Stainless steel shaft Stainless steel lip or mechanical seals for shaft Shielded ball bearings - 1" IPT Weight: 6.2 lbs

Self-priming, very easy to clean.
Will not rust or corrode.
Length: 36".
1-3/4" diameter.
13 GPM pump rate.
Does not include a outlet hose.

Great for emergency situations.

8 strokes for each gallon.

Tough construction with a comfortable hand grip.

Length: 18".

Flexible impeller self priming bronze pedestal pump.
Typical Marine Applications:
-Engine cooling
-Bilge pump
-Wash-down pump
-Emptying holding tanks  
Bronze body. 3/8" NPT ports.  Rated for 6 GPM at 1800 RPM.  Neoprene impeller. 3/8" stainless steel shaft.
Caution: Do not run dry.

Pump with neoprene impeller Bronze body - Stainless steel shaft Stainless steel lip or mechanical seals for shaft Shielded ball bearings - 1" IPT Weight: 6.2 lbs

Pump with oil resistant nitrile impeller Bronze body - Stainless steel shaft Stainless steel lip or mechanical seals for shaft Shielded ball bearings - 1" IPT Weight: 6.2 lbs

Plastic pump body. Nitrile valves and diaphragm. Rated for 8.1 gallons per minute. 1-1/2" ports. 12 volt DC.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/8" discharge outlet.
Model number: 10-6UL.
2000 GPH.
Has 6-foot wire leads for easy installation.

Thirsty-Mate high capacity super pump. Coast Guard approved for commercial use. Model 519CG#2. Three strokes per gallon, rated for 22 gallons per minute. Inlet hose is 24", outlet hose is 72". Length: 24". Diameter: 3". Weight: 8.3 lbs.

Heavy-duty bilge pump. Liquid-cooled, 12-pole motor with double ball bearings. Stainless steel and strong plastic construction. Operates at 120 l/min, 1900 GPH. 4.5 amps, 6 amp fuze. 1-1/8" and 1-1/4" connectors.

A rotary cutter shreds waste before it is pumped into or out of the holding tank The pump should be connected as close as possible to the holding tank discharge outlet or the bowl discharge outlet 15 amp - 1-1/2" hose or 1-1/2" NPT inlet - 1" hose outlet Weight: 5.1 lbs

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
24 volts DC.
1-1/8" discharge outlet.
Model number: 03.
1500 GPH.

Connects to marine engine oil dipstick tubes. Fits threaded male garden hose fitting. Unique design allows one hand pumping. Includes: - Pump with 3/4" brass fitting - Drain hose, 1/2" X 2' length.

All plastic. Self lubricating, self-priming and very easy to clean. Will not rust or corrode. Will not mar boat. Diameter: 1-3/4". Length: 36". Strokes per gallon: 4.

Polypropylene pump body
Rated for 5.2 gallons per minute
Activates at 25 PSI, cuts out at 40 psi
Quiet operation, smooth flow
Has a 2 liter accumulator tank
1/2" hose output
12 volt DC.

Reliable, rugged diaphragm pump.
Portable, lightweight.
All Delrin plastic construction.
Self-priming.
12 foot delivery suction lift.
Horizontal handle orientation.
Inlet / outlet diameter: 1".

1.8 CID hydraulic motor. 2" NPT impeller pump. 2000 maximum RPM. +/- 90 GPM of water at 2000 RPM. 15 GPM of oil required to achieve 2000 RPM. Aluminum bracket.

Sleek, reliable, and compact. Integrated switch. 12 volts. Rated for 1000 GPH. Includes straight and 90° Dura-Port connectors. Has a removable nitrile check valve.

"Full Stroke" Brass Bilge Pumps 7 13 3/4" 22 1/2" 1 3/4" 1" 4 High quality hand bilge pumps: brass cylinders & oil resistant plungers, intake & discharge caps. Includes adjustable mounting brackets for sufficient clearance to easily pump. Meets standards of portable hand bilge: CFR Tile 46, Chapter 1, Subchapter T, Subpart 182.25-10.

Has a high capacity flow rate and horizontal-oriented ports. Rated for 4710 GPH. Self-priming up to 15 feet. Mechanical face type shaft seal. Nitrile impeller. Fitted with single "B" groove pulley. 12 volt.

Marine bronze and stainless steel for reliability. Self-priming. 1-1/4" NPT input. 1" shaft. 1/2" cam.

Inflates a four-man dinghy in 1-2 minutes. Supplied with an adaptor for all major boats. Reversible, will deflate dinghies flat. Single-handed operation. Rated for 550 liters / minute.

"Flat tank" design makes it easy to change your engine oil. Compact, strong and easy to store when not in use. Equipped with a self-priming, run-dry pump. 3.5 gallon capacity. Includes: - Tank with easy-pour spout - 12 volt diaphragm pump - Dipstick-style suction tube - Battery clamp wire leads.

Can deliver almost 7 GPM at open flow.
Equipped with pressure-cast bronze body.
Features a reusable O-ring type end cover seal.
1/2" internal pipe thread and 1" external hose barb.
Includes 2 port adapter.
24 volt DC.

Jabsco 50880 shower drain / bilge pump. A single-diaphragm, 4.2 GPM plastic-body pump. Flexible installation, compact and simple design. Dry-running capability. Pump heads and ports may be rotated during installation. 12 volt.

21" with Float Solid brass piston rod for strength & durability. Easily disassembled for cleaning. 1-1/2" barrel means quick pumpouts. 5 year warranty, Includes 24" of 1-1/8" black bilge flex hose.