Electronic water sensor and pump in one housing.
Provides high pumping capacity and reliability.
Circuit will automatically cycle when needed.
1" and 1-1/8" discharge outlets.
Rated for 2000 GPH.
24 volts DC.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/2" discharge outlet.
Model number: 14A.
3700 GPH.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
Compact, great for small spaces.
Cycles every 2.5 minutes.
Fully automatic, doesn't require float switch.
High efficiency, low amp motor
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
Model number: 27SA, round.
Three wire.
1100 GPH.
(Replaces RUL27S-3.)

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
Model number: 27DA.
1100 GPH.

Designed for washdown or for livewell tanks.
Heavy-duty construction.
Ideal for commercial or pleasure boats.
1-1/2" inlet, 1-1/2" discharge outlet.
Rated for 3700 GPH.
Must be mounted below waterline.
Operates at low pressure; not self-priming.
12 volts DC.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
24 volts DC.
1-1/2" discharge outlet.
Model number: 16A.
3700 GPH.

Fynspray rocker action pump.
May be used with either fresh or salt water.
Self-priming.
Tough non-corrosive white plastic and chrome steel.

Fynspray rocker action pump. May be used with either fresh or salt water Self-priming. Tough non-corrosive black plastic and chrome steel. Weight: 1 lb.

Use for engine cooling, wash down, circulation, and general purposes on-board or dockside Self-priming with ability to operate in either direction at variable speeds Removable end cover for easy impeller service 83 GPM - 2" NIPT - 1" diameter shaft Weight: 21 lbs

Non-automatic; used with a panel and/or float switch.
Submersible and ignition protected.
High-efficiency, low-amp motor (1.6 amps at maximum flow).
Designed not to "burn out" when dry.
Stainless steel shaft.
Includes a back flow prevention device.
Model: 25DA.
Rated for 500 GPH.
3/4" port.
12 volts.

Self-priming drill pump chucks into a standard 1/4" drill motor and pumps up to 3 1/2 GPM (13 L/min). Use for draining engine oil through dipstick tube, pumping, and scavenging jobs, many uses around boat or home. Includes two 3/4" (19mm) garden hose port adaptors mounted on 1/2" barbed port. Weight: .36 lb

Automatic; no float switch needed.
Checks for water every two and a half minutes.
Runs for 1/2 second.
Consumes .2 amps per day.
Submersible and ignition protected.
High-efficiency, low-amp motor (1.6 amps at maximum flow).
Designed not to "burn out" when dry.
Stainless steel shaft.
Includes a back flow prevention device.
Model: 25SA.
Rated for 500 GPH.
3/4" port.
12 volts.

All plastic. Self lubricating, self-priming and very easy to clean. Will not rust or corrode. Will not mar boat. Length: 24". Diameter: 1-3/4". Strokes/Gal: 6. Comes with 6' hose.

All plastic. Self lubricating, self-priming and very easy to clean. Will not rust or corrode. Will not mar boat. Diameter: 1-3/4". Length: 36". Strokes per gallon: 4. Comes with 6' hose.

Bronze pump body. Neoprene impeller. Maximum PSI: 10. Stainless steel shaft. 12 volts DC.

Rated for 4 gallons per minute. Suitable for diesel, fresh or salt water. Includes: - Pump - Spray nozzle - 4 meter cable with battery clips - 4 meter of lay-flat hose. 12 volt DC.

Lever-action pump.
Has a telescoping suction tube that fits 30-55 gallon drum.
Discharge spout has standard garden hose thread.
All steel foot valve and piston valve.

Pacer's S Series self-priming centrifugal pump.
Lightweight and chemically resistant for general service.
Suitable for water, salt water, waste water, and mild acids and bases.
Constructed from polyester.
Stainless steel or non-metallic fasteners for resistance to chemical attack.
Suction lift to 25 ft. (7.6m) vertical.
This model is equipped with a hydraulic motor.
- Requires 9.5 GPM for maximum pumping capacity
- HP required is 5.0
- Up to 230 GPM
- Buna-N elastomers
- Port size : 2" FNPT.

Ideal for simple holding tank pump-outs. Grinds waste into small particles. 1" hose barbed discharge port. Self-priming. Can empty a 30 gallon holding tank in less than 3 minutes. Powdercoated exterior. Sealed bearings to guard against corrosion. Automatic shut-off and sensor for priming pump Dimensions: 3-3/8" X 4-5/8" X 11". Rated for 13 GPM.

Designed to handle large fluid extraction applications. Ideal for removing stagnent bilge fluids. Dual-action pump works on both upstroke and downstroke. Equipped with an automatic shut-off valve to stop overflow. Tethered cap, easy-pour spout prevents messes. Capacity: 5 liters.

Automatic bilge pump.
3/4" discharge outlet.
Senses when bilge water rises and turns on.
12 volt DC.
Rated for 500 GPH.

Comes with kit of tubes and hoses, reducing foot and adapter Use for bilges, sump tanks, transfer, or oil changing from engine crank case, stern drive or inboard. Tube to insert in dipstick hole for oil pump out. Tough marine plastic will not rust or corrode. No priming to start pump action. Red discharge tube, gray hand pump. Weight: .75 lb

Use for engine cooling, wash down, circulation, and general purposes on-board or dockside Self-priming with ability to operate in either direction at variable speeds Removable end cover for easy impeller service 11.3 GPM - 1/2" NIPT - 5/8" diameter shaft Weight: 4.51 lbs

iL500 Plus pump. Suitable for diesel, salt or fresh water. Rated for 500 gallons per hour. Includes: - Pump - Spray nozzle - 4 meter cable with battery clips - 4 meter lay-flat hose. 3/4" ports. 12 volts.

Use for engine cooling, wash down, circulation, and general purposes on-board or dockside Pedestal mount, corrosion resistant bronze pumps Self-priming and portable, very versatile Removable end cover allows easy impeller service Pump heads are built of bronze materials 62 GPM, 1-1/4" NIPT Port, 1" shaft, face seal, brass cam and impeller insert Weight: 12.6 lbs

1.24 CID hydraulic motor. 1-1/2" NPT impeller pump. 2000 maximum RPM. +/- 70 GPM of water at 2000 RPM. 11 GPM of oil required to achieve 2000 RPM. Aluminum bracket.

1.24 CID hydraulic motor. 1-1/4" NPT impeller pump. 2000 maximum RPM. +/- 55 GPM of water at 2000 RPM. 11 GPM of oil required to achieve 2000 RPM. Aluminum bracket.

Can deliver almost 7 GPM at open flow. Equipped with pressure-cast bronze body. Features a reusable O-ring type end cover seal. 1/2" internal pipe thread and 1" external hose barb. Includes 2 port adapter. 12 volt DC. Weight: 6.06 lbs

Designed for the tough demands of the fishing industry. Equipped with a liquid-cooled 12-pole motor. Features a mechanical shaft seal and a threaded port. Uses 1-1/8" ports. Rated for 1600 GPH.

Designed for automatic operation with an Ultima switch.
Rated for 1000 GPH.
Equipped with easy-to-install Dura-Port discharge ports.
3/4" fitting.

Provides high pumping capacity and reliability.
All-in-one pump and intelligent switch.
Designed to activate at 2-1/2" deep water.
Circuit will automatically cycle when needed.
1" and 1-1/8" discharge outlets.
12 volts DC.

Nylon pump body. Rated for 3.5 gallons per minute. Activates at 25 PSI, cuts out at 40 psi. Quiet operation, smooth flow. Compact design. 3/8" port, 1/2" hose output. 12 volt DC.

Johnson Aqua Jet water pressure system. A postive displacement diaphragm pump for small craft. Works great for pressurized water supply systems. Rated for 3.5 GPM. 3/8" NPT, 1/2" hose ports. Weight: 5.5 lbs.

Replaceable wear plate to extend service when handling abrasive fluids
9.5 GPM - 115 Volt Motor - 1/3 HP - 1/2" NIPT
Dimensions: 7-3/4"H x 7-1/4"W x 10-1/2"L

Jabsco 50890 waste pump. A single-diaphragm, 5 GPM plastic-body pump. This self-priming pump is designed to pass debris. No filter required. OK to run dry and equipped with a 360º rotatable head. 12 volt.

Thermoplastic pump body. Rated for 5 gallons per minute. Stainless steel shaft. 3/4" ports. 12 volts DC.