Single-layer, corrugated polyethylene hose.
Resistant to mild chemicals and salt water.
Has a clamping cuff every foot.
This hose is primarily used for bilge pump discharge.
Diameter: 3/4".
Color: White.
50 feet per carton.

Mounting hardware kit for single S control.  
Includes instructions. 

Mounting hardware kit for Twin SR control.
Includes instructions. 

Shields 400/402 Vinylvent Vent Hose 4" 4 1/8" 10 White Venting of bilge gases & fumes. PVC hose supported by helical wire. Resistant to ozone, sunlight and weathering. Will not support a flame.

Single-layer, corrugated polyethylene hose.
Resistant to mild chemicals and salt water.
Has a clamping cuff every foot.
This hose is primarily used for bilge pump discharge.
Diameter: 5/8".
Color: White.

Smooth cover, clear PVC with white vinyl helix. Rated for full vacuum. Resistant to mild chemicals and saltwater. Used for: - Bilge pump intake and discharge - Livewell intake and drain - Sanitation: intake, vent and pump out. Designed for connections below the waterline. Not for use in pressurized systems or with antifreeze. Diameter: 3".

Single layer vinyl, non toxic clear tubing. FDA approved. Useful for sink, cooler, or livewell drain lines. Not recommended for hot water. Diameter: 1/2".

Ball joint with quick release stud.
Plated steel.
For 40 series cable.
5/16" stud.

PVC hose with a flexible vinyl helix. Very flexible, abrasion, salt and chemical resistant. Used for bilge pump discharge and drains. Size: 3/4".

SL-3 side mount control mounting plate.  
Includes mounting hardware. 

30 series.
Stud diameter: 3/16".
Lever thickness: 1/8".
Length: 11/16".

Non-permeable fuel line. Polyester reinforced. CPE weather and UV-resistant cover. ID: 3/8".

Back mount rack helm.
Standard 3/4" round tapered steering shaft.
16" maximum steering wheel diameter.
Precise, 4-turn response.
Accepts SeaStar SSC134, SSC135, and SSC154 rack steering cables.
Included in SeaStar SS141 steering system kits.

30 series cable clamp bracket.
Plated steel. 

14" black 3 spoke steering wheel with center pad.
Hard PVC grip.
Beautiful, high-detail styling.
Rugged construction for marine use.
U.V. and corrosion resistant materials.
Stylish center medallion included.
Fits standard 3/4" tapered shaft.
Suitable for mechanical steering.

Flows at 90 GPH. Port size: 3/8". Includes: - 21 micron filter - Brass plugs - Stainless steel head.

Single-lever, dual action - throttle and shift control.  
Surface mount design for quick, tidy installation.
Includes neutral warm up capability.
Includes hardware for two 33C type cables.
Positive shift detents and neutral lock-out.
Weatherproof exterior, rugged die cast frame.
Meets/exceeds all applicable industry standards.

60 series. Diameter: 3/8".

Replacement plastic cover for SeaStar SL-3 side mount control. 
Rectangular shape.  
Snaps into place.

Hardware & bearings kit for Twin S control.  
For use with 33C series cables.

Double-ply soft wall, no wire.
For straight connection in wet exhaust systems.
Okay for either gasoline or diesel engines.
Designed for coolant and heat resistance.
Color: Black with blue stripe.
Temperature range: 0° to 212° F.
Diameter: 3-3/4".
Length: 12.5 feet.

Prevents unwanted torque at the wheel.
For all V-4 and smaller outboards.
3 turns lock-to-lock.
Uses QC II (SSC62) steering cables.
Collet and hitch pin secures QC cable to helm
Single station.

For throttle, choke, or other options. Attaches to Morse 33C cables.

Steering cable tube support kit with mounting bracket.
For older model outboards without tilt tubes,
low HP outboards or applications where design
interferes with standard tilt tube mounting.
Galvanized steel.

60 series. Diameter: 5/16".

Dual station kit for SeaStar CH5600P control.
For use with 33C series cables.
Includes instructions. 

Dual station adapter kit for adapting throttle
or clutch from 33C series cable to 43C series cable.  
Includes instructions.

Smooth cover, clear PVC with white vinyl helix. Rated for full vacuum. Resistant to mild chemicals and saltwater. Used for: - Bilge pump intake and discharge - Livewell intake and drain - Sanitation: intake, vent and pump out. Designed for connections below the waterline. Not for use in pressurized systems or with antifreeze. Diameter: 3/4".

Dual station kit for Twin S controls.
For 33C series cables.

Dual station kit for S & Twin S controls.  
2 required for Twin S control.
For 43C series cables.

Vertical bleed tee.
#5MORB X 3/8" compression x bleed nipple.  
Two per package.

Horizontal bleed tee.
#5MORB X 3/8” compression x bleed nipple.
Two per package.

90˚ elbow.
#5MORB X 3/8” compression.  
Two per package.