Nitrile. 10 blades. Diameter: 1-9/16".

Replacement bearing for Jabsco pumps.

Same pump used in Jabsco multi-engine oil change system Can change oil in a typical V-8 in minutes 3/8" NPT male threaded Dimensions: 7-1/8"L x 3-3/4"W

For 6050, 6850 series pumps. Includes seal, gasket, impeller.

For 6050, 6850 series pumps. Includes seal, gasket, impeller.

Operates by the rotary sliding vane principle Has vectra rotor and vanes that are designed to handle oil or diesel fuel transfer Pumps up to 5-1/2 GPM and transfers diesel fuel from a 55 gallon drum in 10 minutes Self-priming to 3 feet - Low amp draw Vane Puppies are equipped with a high torque motor with ball type shaft bearings Rated for continuous duty operation Bronze pump has ports with 1/2" internal pump thread 1" external hose barb Also supplied are port adaptors for 3/4" gallon hose thread. Weight: 6.4 lbs

Replacement cam liner for impeller pumps. Used with Jabsco 17360 model.

Replacement bearing for Jabsco pumps.

Electromagnetic clutch pumps equipped with a powerful electric clutch for convenient remote operation 12 volt model Capable of operating through a wide range of speeds and in either rotational direction 1B Pulley Belt Grooves - 1" NIPT - 26 GPM Weight: 14.75 lbs

Three per bag.

Strains debris and particles from bilge pump line. Clear plastic housing for easy inspection. Easy to disassemble and clean. 16 mesh stainless steel screen. 3/4" hose barb ports.

High impact plastic construction. Will not rust, corrode or discolor. Designed for use with Rule pumps. Size: 3/4".

Keeps debris from entering your pump. Plug-in Quad port. Threaded bowl makes cleaning easy. 40 mesh, stainless steel screen. 3/4" hose barb.

Cam screws for Jabsco pumps. Pack of three.

Reducing hose adapter. 1" to 1-1/2".

Keep your decks clean with this high-flow and high-pressure diaphragm pump kit.

A HD model that features a heavy-duty motor and cast aluminum lower housing.
Efficient, quiet and self-priming.
Runs dry without damage.
Quick-connect ports make it easy to install and service.
Kit includes 25 feet of coiled hose and a spray down nozzle.

For 1673, 777 series pumps. Used with seal spacer and O-ring on pump shaft. Diameter: 1-1/8".

End cover gasket. Fits many Jabsco pumps.

For 12210 pump. Includes impeller, gasket, hardware.

Includes gasket and five vanes. Use with 18680 series Jabsco pumps.

For use with 82605 series pump.
Rated for 70 PSI.

Used in retrofits of crank driven pumps. For Volvo, Indmar, and Marine Power engines.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
Cycles every 2.5 minutes.
Fully automatic, doesn't require float switch.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/2" discharge outlet.
Model number: 55S.
3700 GPH.

For Jabsco electromagnetic clutch. 12 volts.

Rated for 60 PSI. For 32605 series pumps.

For Jabsco pumps. Three per bag.

Replacement inner seal for Jabsco pumps. For 777 series pumps.

Jabsco pump head, model 18610-0001 1/2" NPT ports with garden hose adapters Weight: 2.75 lbs

Steel. Three per bag.

Check valve for Jabsco pump.

A variable speed drive system. Adds pressure-sensor control to everyday pumps. Senses real-time changes in pressure. Provides smooth and pulsation-free performance. Works on most water presure systems. 12 volts.

"Snap-In" straight port kit.
1/2" hose barb connectors.
Two per package.