Inline Check Valve 1-1/2" Fits in pumps suction hose to aid priming & prevent backflow.

Inline Check Valve 1" Fits in pumps suction hose to aid priming & prevent backflow.

3-Way Hose Fitting "T" 1-1/8" for Bilge Hose

For Jabsco pumps. Three per bag.

Prevents particles from entering pump. Cuts down on repairs, easy to install. Transparent housing for quick inspection. 50 mesh stainless steel filter screen. 3/4" hose barb ports.

Prevents particles from entering pump. Cuts down on repairs, easy to install. Transparent housing for quick inspection. 50 mesh stainless steel filter screen. 3/4" hose barb ports, one bottom port for 90° installations.

Replacement micro switch for Jabsco Par-Max 44010 & 44020 series water systems.

Main control station. Can connect to selector panel and searchlight. 12 volt DC.

For use with Jabsco remote-control searchlights. 12 volts. 50 watts.

Keep your decks clean with this high-flow and high-pressure diaphragm pump kit.

A HD model that features a heavy-duty motor and cast aluminum lower housing.
Efficient, quiet and self-priming.
Runs dry without damage.
Quick-connect ports make it easy to install and service.
Kit includes 25 feet of coiled hose and a spray down nozzle.

For 1673, 777 series pumps. Used with seal spacer and O-ring on pump shaft. Diameter: 1-1/8".

End cover gasket. Fits many Jabsco pumps.

For 12210 pump. Includes impeller, gasket, hardware.

Includes gasket and five vanes. Use with 18680 series Jabsco pumps.

For use with 82605 series pump.
Rated for 70 PSI.

Used in retrofits of crank driven pumps. For Volvo, Indmar, and Marine Power engines.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
Cycles every 2.5 minutes.
Fully automatic, doesn't require float switch.
High efficiency, low amp motor.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
1-1/2" discharge outlet.
Model number: 55S.
3700 GPH.

For Jabsco electromagnetic clutch. 12 volts.

Rated for 60 PSI. For 32605 series pumps.

For Jabsco pumps. Three per bag.

Replacement inner seal for Jabsco pumps. For 777 series pumps.

Jabsco pump head, model 18610-0001 1/2" NPT ports with garden hose adapters Weight: 2.75 lbs

Steel. Three per bag.

Check valve for Jabsco pump.

A variable speed drive system. Adds pressure-sensor control to everyday pumps. Senses real-time changes in pressure. Provides smooth and pulsation-free performance. Works on most water presure systems. 12 volts.

"Snap-In" straight port kit.
1/2" hose barb connectors.
Two per package.

Rated for 25 PSI. For 31200 series pumps.

Use for diesel fuel transfer, liquid transfer jobs, dockside pumping, dewatering or circulation, engine oil changing Fitted with oil resistant elastomers Self-priming, may be mounted above the waterline Heavy-duty ball bearings, thermal overload protection Continuous duty motor provides quiet operation & smooth flow Runs dry without harm to pump Includes plug-in ports for easy installation, two garden hose ports and two 3/4" hose barb ports Includes a 3/4" inlet strainer Weight: 6 lbs

Self-priming pump with run-dry protection. Triple-sealed motor to prevent corrosion. Four-bladed chopper reduces clogging. Flow rate: 12 GPM. Self primes up to 4 feet of vertical lift. Ports: 1-1/2" and 1". 24 volts DC, 8 amp draw.

Jabsco pressure switch. Rated for 25 PSI.

Cam screws for Jabsco pumps. Pack of three.

Jabsco pressure switch. 50 psi. For use with 31700.

Black plastic construction.

For 36950 diaphragm pump. Includes diaphragm, valve set, and dampeners.