For GM engine pumps. Used with 18330, 18370, 17360 series.

Neoprene. 10 blades. Diameter: 2-9/16".

For Jabsco 777 series pumps. Inner hole: 1-1/16".

Cam screws for Jabsco pumps. Pack of three.

Place pump end in low point of bilge and powerful self-priming action gives full suction on first stroke. Quick, easy pump out of bilges and other flooded areas Compact, easy to stow, only 17" (430mm) long Includes 5 ft. length of 1/2" discharge hose Weight: 1.7 lb

For Jabsco impeller pump, model 1673.

Prevents particles from entering pump. Cuts down on repairs, easy to install. Transparent housing for quick inspection. 50 mesh stainless steel filter screen. 3/4" hose barb ports, one bottom port for 90° installations.

Equipped with a Viton O-ring. Quad port X 1" hose barb connector. Two per package.

Prevents particles from entering pump. Cuts down on repairs, easy to install. Transparent housing for quick inspection. 50 mesh stainless steel filter screen. Slip-on 1/2" ports.

Quick, easy and clean oil changes at flip of a switch Removes oil/sludge through dip stick tube so engine oil changes quick and easy. No spill under engine. Oil changer supplied with both 1/4" x 40" dipstick probe and a female garden hose connector that attaches suction hose directly to dipstick tubes supplied with male garden hose threads. Reversible pump so container is emptied neatly/easily by reversing flow direction. Retractable pouring spout if not desirable to use pump for emptying. 12 volt model with 8' cord and alligator clips. Simply connect power cord to appropriate electrical source. With flick of switch sturdy motor pump unit drains crankcase into its 14 qt. holding container. Dimensions: Height 13-5/8", Width 13-1/2" 
 

Neoprene. 12 blades. Diameter: 2-1/4".

Nitrile. 12 blades. Diameter: 2-1/4".

Neoprene. 10 blades. Diameter: 2-9/16".

Designed to remove water from basements, garages, stairwells, utility rooms, back yards, sumps, pools, pool covers, boats and more.
Fully-automatic version uses standard 110 volt AC current
8' cord.
1800 GPH.

Brass construction. For Jabsco pumps repairs.

T-Handle pump for 29090 toilet Weight: 1.85 lb

A lighter, compact pump for smaller vessels.
Tough plastic body with integral strainer.
Quick-release inlet strainer allows for quick cleaning.

12 volt DC.
3/4" hose connections.
Output: up to 23 liters per minute.

Includes a Rule 35A non-mercury float switch.

A compact, general-purpose pump. Bronze body. Nitrile impeller. 3/8" ports. Rated for 3.4 gallons per minute at 10 feet. Stainless steel shaft. 6 foot cord, with AC plug.

"FC" Tournament series pump.
Rated for 1100 gallons per hour.
Features removable motor cartridge.
1-1/8" ports.
12 volts.

Electromagnetic clutch pumps equipped with a powerful electric clutch for convenient remote operation 12 volt pump Capable of operating through a wide range of speeds and in either rotational direction. Dimensions: 2A Pulley Belt Grooves - 2" NIPT - 83 GPM Weight: 30.5 lbs

For pumps: 4305, 4405 and 4325. Weight: .4 lb

Jabsco general-purpose pump. Used for cooling, wash down, circulation and more. Pedestal-mount, corrosion-resistant bronze construction. Self-priming and portable: very versatile. Removable end cover allows easy impeller servicing. 1" shaft, 1-1/4" NIPT port, rated for 62 GPM. Weight: 10.19 lbs.

Provides ultimate pumping performance and fully automatic operation.
Designed to help keep your boat clear of nuisance water.
Equipped with a powerful 800 GPH high-capacity pump.
Tough impact-resistant sealed polycarbonate lid.
3/4" discharge port.
Simple to install.

Replacement lip seal for pump.
For series 777-9001, 1673-9001.

Nitrile. 6 blades. Diameter: 2".

Neoprene. 6 blades. Diameter: 2".

For use with 3" ducting.

Output: 105 cubic meters per minute.

For use in engine rooms, galleys or heads.

Flange designed to mount directly to bulkhead.

Corrosion-resistant.

A multi-purpose hand pump kit. Brass and neoprene construction. Corrosion resistant. Great for draining or filling engine and gearbox oil. Rated for up to 1-1/2 GPM output. Includes: - Pump - Two 1/2" hoses, 3 feet length - Two dipstick probes, 1/4" and 5/16" - Connector and adapter for 1/2" hose. Not designed for pumping flammable liquids.

Size: 1/2".
For hose connections.
Two per package.

Includes: - 3 feet of 1/2" hose - Probe adaptor - 1/4" X 40" dipstick probe - Utility pump. Kit has same utility pump as 17250-0003. Packed in poly bag with display header card.

FC Tournament Series pump.
For seacock applications.
3/4" intake.
3/4" discharge hose.
Flow rate: 800 GPH.
12 volts.

Bronze impeller pump. Can handle small bilge debris. Flow rate: 8 GPM. 12 volts.

End cover gasket. Fits 2" Jabsco pumps.

For Jabsco pumps. Three per bag.

Neoprene. 9 blades. Diameter: 2".

Prevents particles from entering pump. Cuts down on repairs, easy to install. Transparent housing for quick inspection. 50 mesh stainless steel filter screen. Slip-on 1/2" ports.