Engineered to repel water and remove contaminates. For model 120A filter assemblies. Filter is 2 microns. Rated for 15 GPH.

Rated for 30 GPH. 10 micron filter. Fits the Racor 120A, 120R, 122R, and 140R.

Engineered to repel water and remove contaminates.
Used as a primary filter for 500 series turbine assemblies.
Rated for 60 gallons per hour. Filter is 30 microns.

Racor fuel filter / water separator turbine with three-stage filtration.
Provides maximum protection of diesel engine components.
Effectively removes contaminants from fuel.
Filters out water, silica, sand, dirt, rust and more.
See-through bowl.
2 micron element included.
Max flow rate: 90 GPH.
Port size: 5/8" ORB.
Replacement element: 2040N series.
 
Dimensions: 16.5"H X 5.96"W X 5.96"D.

Rugged corrosion-resistant steel construction. Wide studded band prevents crushed filters. Fits 2-13/16" to 3-5/32" diameter oil filters.

Clutch detent kit for single station
S and Twin S controls.
Includes installation instructions.

For connecting 20 and 30L series cable to lever.
3/32" diameter hole for wire.
1/4" diameter stud.
1/8" lever thickness.

Inside mount. Rectangular flange. Complete with packing nut and lock nut. Shaft size: 2". Packing size: 3/8".

Allows the MT-3 control to be used with 43C series cables. Includes parts and instructions.

Cable clamp shim for 30 series control cables.
Used with 32010 clamp.
7/8" center to center bolt pattern.
Overall dimensions: 1-3/8" X 1/2".
Aluminum construction.

Dual station kit for Twin SR control.
For 43C series cables.
Two required for twin lever controls.

Stamped 304 stainless steel. Designed to protect cables and electrical wiring. For use with transom holes. Size: 1-1/4" X 3/4".

For use with electric trolling motors and some outboards. Clamps directly to tiller handles. Provides full access to kill button. Rated for use up to 15 horsepower motors. Fixed length: 18".

For use with electric trolling motors and some outboards. Clamps directly to tiller handles. Provides full access to kill button. Rated for use up to 15 horsepower motors. Adjustable length: 18" - 24".

For 20 series control cables.

For Morse 80 series control systems.
Diameter: 5/16".

DURAMAX Ultra-X graphite packing. Engineered specifically for heavy-duty marine use. 300% lower friction than flax packing. Provides superior thermal conductivity. Grease free installation. Virtually eliminates shaft scoring. Approximately 13 feet per roll. Thickness: 5/16". Weight: 1 lb.

Gives high performance with minimal backlash. Uses a unique splined core wire for smooth control. 4" minimum bend radius, 10-32 threaded ends. Replaces all universal type (33 series) control cables. Size: 324" (27 feet).

Mounting hardware kit for single S control.  
Includes instructions. 

Mounting hardware kit for Twin SR control.
Includes instructions. 

Anodized aluminum and stainless steel construction. Holds speeds as low as 1 mph. Patented hinged design flexes to prevent bending. Fits outboard and inboards, 30 - 300 horsepower.

Synthetic yarn, thoroughly impregnated with graphite Dense sealing material, with petroleum-based lubricant. Designed to resist water, oils, and chemicals. Color: Black. Thickness: 5/16". 22 feet per roll.

Ball joint with quick release stud.
Plated steel.
For 40 series cable.
5/16" stud.

Converts 5/8" bolt holes to 1/2" flange holes. Includes bushings and washers. Used with Globe Drivesavers.

SL-3 side mount control mounting plate.  
Includes mounting hardware. 

30 series.
Stud diameter: 3/16".
Lever thickness: 1/8".
Length: 11/16".

Custom built for smaller boats. Carefully machined to leave correct clearance. Brass shells, chemical resistant nitrile rubber interiors. Dimensions: 2" X 2-5/8" X 8".

30 series cable clamp bracket.
Plated steel. 

For use with electric trolling motors and some outboards. Clamps directly to tiller handles. Provides full access to kill button. Rated for use up to 15 horsepower motors. Fixed length: 30".

Ideal for gas outboards and electric trolling motors Clamps directly to tiller handles (fits all tiller handles) Marine grade materials - Full access to kill button Works effectively on all motors up to 15 HP Straight handle for direct steer feel Extendable length: 36" to 50" Lifetime warranty

Ideal for gas outboards and electric trolling motors Clamps directly to tiller handles (fits all tiller handles) Marine grade materials - Full access to kill button All metal universal joint for easy push/pull steering Lockout sleeve converts handle for direct steer feel Works effectively on all motors up to 15 HP Straight handle for direct steer feel Extendable length: 37" to 51" Lifetime warranty.
Please contact Seattle Marine at 1-800-426-2783 for shipping options. 

Ramie yarn, thoroughly impregnated with paraffin. Square plait construction, coated with mineral oil. Designed to resist water, oils, and chemicals. Color: Off-white. Thickness: 9/16". 6.5 feet per roll.

60 series. Diameter: 3/8".

Replacement plastic cover for SeaStar SL-3 side mount control. 
Rectangular shape.  
Snaps into place.

Hardware & bearings kit for Twin S control.  
For use with 33C series cables.