Seal and O-ring kit for SeaStar Hynautic K-1 and PSK-10 cylinders.

For use with MRB80A actuator. Includes installation diagram.

For use with MRB75A actuator. Includes installation diagram.

For use with MS55L cylinder. Includes installation diagram.

Oil reservoir plug. For use with InstaTrim boat leveler systems. Weight: .01 lb.

Package of 10 quad rings. Part number HS6038.

Rubber construction. O-rings. Thickness: .210". 20 per package.

Female wiring receptacle. Used with Trim Tab boat leveling systems. Weight: .4 lb.

Housing for boat leveler motor and pump. Built from high-impact ABS plastic. Mounts easily with two screws. For use with Trim Tab boat leveler systems. Size: 4-1/2" X 6" X 11" Weight: 1.17 lbs

For MRB50 / 63.

Seal and O-ring kit.                    
For pre-8000 Hynautic H-80 series helms.

Seal and O-ring kit.                    
For post 1979 Hynautic H-40 series helms.

Seal and O-ring kit.                    
For pre-1978 Hynautic H-40 series helms.

Seal and O-ring kit.                    
For post 1979 Hynautic H-20 series helms.

Seal and O-ring kit.                    
For pre-1978 Hynautic H-20 series helms.

T-shaped brass hose fitting. Provides a three way split in hose lines. For use with InstaTrim boat leveler systems. Weight: .1 lb.

12 volt green solenoid for Trim Tab systems. Custom design is epoxy sealed for water resistance. These solenoids lock the tabs in any postion. Barb-type hose fittings for a secure connection. For use with InstaTrim boat leveler systems. Weight: .36 lb.

For use with MSB-35 cylinder. Includes installation diagram.

For use with MS-42 cylinder. Includes installation diagram.

Surface-mounted audio/visual alarm. Buzzer and red light activates when water is detected. Does not have "mute alarm" option. Buzzer sounds until water is drained from fuel filter bowl.

Spin-on filter. Dimensions: 9-19/32" X 4-21/32"

Secondary fuel filter, spin-on.
Fits: Case consolidated Diesel Cummins engines; Komatsu equipment.

2 micron. For secondary (final) filtration. Includes seals.

Built to strict OEM standards. Designed for use with Yamaha outboard systems. Attaches to the fuel hose on the engine side. Size: 5/16".

Designed to absorb angular prop thrust loads. 
Heavy-duty aluminum casting. 
Oil and fuel resistant elastomer element. 
Comes complete with nuts and washers. 

Kit includes:
- Clear bowl
- Replacement gasket
- 1/2" SAE plug.

Water-absorbing fuel storage tank element.
Absorbs up to 3 ounces of water over life span of filter.
Flow rate: 25 GPM pumped, 10 GPM gravity fed.
15 micron.
1-1/8" mounting stud.
Length: 4-7/8".

Spin-on fuel filter / water separator assembly. For gasoline fuel only. Flow rate: 30 GPH. Uses Aquabloc II filter element, 10 micron. Has a see-through bowl with a drain. Dimensions: 6-1/2" tall, 3-1/4" diameter.

Connects fuel line assemblies and fuel tanks. Built to OEM specifications. For Yamaha engines.

Outside diameter: 3-11/16".
A full-flow lubricant filter unit.
Thread: 3/4" - 16.
#BT216.
Compatible with Perkins 2654403.

For Yamaha outboard engines. Size: 5/16". Mates with tank connector. Packaged for retail display.

For Yamaha outboard engines. Size: 1/4". Mates with tank connector. Packaged for retail display.

For Yamaha outboard engines. Size: 1/4". Mates with tank connector. Packaged for retail display.

For 900/1000.
Coverts older models to meet the new ABS rules.
Part number: RK11734.

Racor fuel filter / water separator turbine
with three-stage filtration.
UL-approved.
Provides maximum protection of diesel engine
components.
Effectively removes contaminants from fuel.
Filters out water, silica, sand, dirt, rust and more.
Equipped with see-through bowl with metal heat
shield.
2 micron element included.
Maximum flow rate: 90 GPH.
Port size: 5/8" MJIC.
Replacement element: 2040N series.
Dimensions: 16.2"H X 5.96"W X 6.76"D.