Hydro-slave pot hauler block. Equipped with a 1006 Char-Lynn motor. Complete with extra heavy anodized cast aluminum housing. - Stainless steel discs. - Cadmium-plated disc liners. - Stainless steel center hub and splitter. - Aluminum fairlead rollers with stainless steel shafts. Ports are 1/2" NPTF with 45° hydraulic fittings.

Hydro-slave pot hauler block. Equipped with a 1004 Char-Lynn motor. Complete with extra heavy anodized cast aluminum housing. - Stainless steel discs. - Cadmium-plated disc liners. - Stainless steel center hub and splitter. - Aluminum fairlead rollers with stainless steel shafts. Ports are 1/2" NPTF with 45° hydraulic fittings. Provides 600 lbs line pull, 22 RPM per gallon.

Plated steel. #12 female JIC to #16 male JIC.

Open center. 20 GPM rated flow. 3625 PSI maximum work pressure. P, A, and B port #10 SAE O-ring ports. T port #12 SAE O-ring ports. Spring to center with fourth position float. Fourth position allows for anchor winch free wheel. Nickel plated spool.

Stainless steel.
37° flare.
With lock nut.

Fits Walvoil DPX100 or SDS100 work sections.

Load sense.
Clockwise rotation.
Not torque limiting.
Displacement: 4.6 cubic inches.
Front drive flange: SAE C 4-bolt.
Rear drive flange: SAE A 2-bolt.

Load sense.
Counterclockwise rotation.
Not torque limiting.
Displacement: 4.6 cubic inches.
Front drive flange: SAE C 4-bolt.
Rear drive flange: SAE B 2-bolt.

FNPTS to MNPT.

Naiad Dynamics complete bow thruster, model 8HT.

Designed for vessels from 38 - 48 feet in length.
Features a custom-engineered, highly skewed propeller.
This sleek thruster assembly is extremely quiet.
Stainless steel construction throughout.
Built to give a long, reliable marine service life.

Engine, pump, tank, filter: a self-contained unit.
Fully assembled and mounted with stainless steel fasteners.
Marine-grade aluminum base with aluminum handle.
8 GPM 4-stroke, 9 horsepower Honda gasoline engine.
Suitable for powering 12" hauler head assemblies.

NOTE: Engine on this power pack is shipped WITHOUT oil.  Fill engine with oil to proper lever before starting.

NOTE: Due to the size of this product, shipping via UPS or USPS may be cost prohibitive.
Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Hydraulic steering control unit.
Closed center.
Non-load sense.
NBR seals.
Connection: 3/4" - 16 UNF.
Maximum input pressure: 175 bar (2500 PSI).
Maximum continuous backpressure: 25 bar (360 PSI).
VFU: 125.
Flow rating: 12.5 liters / minute.
Displacement: 7.3 cubic inches.

For WFD 101 motor.

High-pressure through-deck (bulkhull) fitting. Stainless steel construction. Rated for 3000 psi, for use with hydraulic systems. Two female NPT ports: 3/4". Overall dimensions: 5.5" X 3".

Open center / cylinder spool. 20 GPM rated flow. 3625 PSI maximum work pressure P, A and B ports #10 SAE O-ring. T port #12 SAE O-ring. Spring to neutral. Nickel-plated spool.

Nitrile tube, reinforced with two braids of high tensile steel wire. For use with water and petrochemicals like hydraulic fluid, diesel fuel, lubricants, and gasoline.

Features:

• Black, weather-resistant synthetic rubber covering
• 5/8" inner diameter
• Temperature rating: -40°F to +212°F
• Maximum working pressure: 3625 psi
• Minimum burst pressure: 14,500 psi

*Flextral part number PX250-10, #10

Nitrile tube, reinforced with two braids of high tensile steel wire. For use with water and petrochemicals like hydraulic fluid, diesel fuel, lubricants, and gasoline.

Features:

• Black, weather-resistant synthetic rubber covering
• 3/4" inner diameter
• Temperature rating: -40°F to +212°F
• Maximum working pressure: 3125 psi
• Minimum burst pressure: 12,500 psi

*Flextral part number PX250-12, #12

Nitrile tube, reinforced with two braids of high tensile steel wire. For use with water and petrochemicals like hydraulic fluid, diesel fuel, lubricants, and gasoline.

Features:

• Black, weather-resistant synthetic rubber covering
• 1" inner diameter
• Temperature rating: -40°F to +212°F
• Maximum working pressure: 3000 psi
• Minimum burst pressure: 12,000 psi

*Flextral part number PX250-16, #16

Nitrile tube, reinforced with two braids of high tensile steel wire. For use with water and petrochemicals like hydraulic fluid, diesel fuel, lubricants, and gasoline.

Features:

• Black, weather-resistant synthetic rubber covering
• 1-1/4" inner diameter
• Temperature rating: -40°F to +212°F
• Maximum working pressure: 2250 psi
• Minimum burst pressure: 9,000 psi

*Flextral part number PX250-20, #20

Parker hydraulic gear pump. Compact, lightweight pump, great for low-flow applications. Simple, efficient pressure-loaded design; few moving parts. Highly tolerant to fluid contamination. Very reliable in cold weather. Maximum flow: 11.3 gallons per minute. Maximum pressure: 2500 psi. 3/4" ORB inlet, 5/8" ORB outlet. Shaft size: 3/4". SAE A 2-bolt mounting.

Parker hydraulic gear pump. Compact, lightweight pump, great for low-flow applications. Simple, efficient pressure-loaded design; few moving parts. Highly tolerant to fluid contamination. Very reliable in cold weather. Maximum flow: 5 gallons per minute. Maximum pressure: 2500 psi. Shaft size: 1/2". 4-bolt mounting.

Parker hydraulic gear pump. Compact, lightweight pump, great for low-flow applications. Simple, efficient pressure-loaded design; few moving parts. Highly tolerant to fluid contamination. Very reliable in cold weather. Maximum flow: 7.9 gallons per minute Maximum pressure: 2500 psi. Shaft size: 1/2". SAE A 2-bolt mounting.

Walvoil EX38 full flow sharing sectional valve. 
- Pressure-compensated flow control work sections 
- Sectional valve (1-10 sections) 
- Load sensing 
- Full flow pressure relief 
For use with mechanical, hydraulic, 
pneumatic and proportional electro-hydraulic controls. 
Manually actuated, spring to center spool. 
22 GPM. 
#10 SAE ORB work ports.

Steel.
#8 FJIC.

Steel end cap.
#6. FJIC.

Steel end cap.
#4. FJIC.    

Hydro-slave bulkhead pot hauler. Equipped with a 1003 Char-Lynn motor. Complete with extra heavy anodized cast aluminum housing. - Stainless steel discs. - Cadmium-plated disc liners. - Stainless steel center hub and splitter. - Aluminum fairlead rollers with stainless steel shafts. Ports are 1/2" NPTF with 45° hydraulic fittings. Provides 380 lbs. line pull, 35 RPM per gallon.

Nitrile tube, reinforced with two braids of high tensile steel wire. For use with water and petrochemicals like hydraulic fluid, diesel fuel, lubricants, and gasoline.

Features:

• Black, weather-resistant synthetic rubber covering
• 1/4" inner diameter
• Temperature rating: -40°F to +212°F
• Maximum working pressure: 5805 psi
• Minimum burst pressure: 23,220 psi

*Flextral part number PX250-04, #4

Nitrile tube, reinforced with two braids of high tensile steel wire. For use with water and petrochemicals like hydraulic fluid, diesel fuel, lubricants, and gasoline.

Features:

• Black, weather-resistant synthetic rubber covering
• 3/8" inner diameter
• Temperature rating: -40°F to +212°F
• Maximum working pressure: 5000 psi
• Minimum burst pressure: 20,000 psi

*Flextral part number PX250-06, #6

Nitrile tube, reinforced with two braids of high tensile steel wire. For use with water and petrochemicals like hydraulic fluid, diesel fuel, lubricants, and gasoline.

Features:

• Black, weather-resistant synthetic rubber covering
• 1/2" inner diameter
• Temperature rating: -40°F to +212°F
• Maximum working pressure: 4250 psi
• Minimum burst pressure: 17,000 psi

*Flextral part number PX250-08, #8

Hydraulic quick-connect fitting.
#6.
Size: 3/8".
Rated for 0 - 3000 PSI.

Long handle. 
Length: 210mm long. 

For use with a Char-Lynn 101 H-series motor.