Cast bronze Cast hex for easier installation Curved 90 degrees Pipe Size: 1" Hose Size: 1" Overall Length: 4-3/4" Weight: .6 lbs

Fuel filter with shut-off valve. A perfect filter for a Dickinson stove. Stainless steel and glass filter. Stone element included. Part # 20-010. Weight: .6 lbs

Quick, easy and clean oil changes at flip of a switch Removes oil/sludge through dip stick tube so engine oil changes quick and easy. No spill under engine. Oil changer supplied with both 1/4" x 40" dipstick probe and a female garden hose connector that attaches suction hose directly to dipstick tubes supplied with male garden hose threads. Reversible pump so container is emptied neatly/easily by reversing flow direction. Retractable pouring spout if not desirable to use pump for emptying. 12 volt model with 8' cord and alligator clips. Simply connect power cord to appropriate electrical source. With flick of switch sturdy motor pump unit drains crankcase into its 14 qt. holding container. Dimensions: Height 13-5/8", Width 13-1/2" 
 

Heavy-walled FDA-approved vinyl compound. Reinforced with polyester braid. Non-toxic, tasteless, odorless. Red tracer in clear PVC. Appropriate for: - Hot/cold pressurized water systems - Vent and drain lines - Bilge pump discharge. For temperature range: 25° F - 150° F. Rated for a burst pressure of 250 psi. Size: 5/8".

Reliable, rugged diaphragm pump. Portable, lightweight. All Delrin plastic construction. Self-priming. 12 foot delivery suction lift. Vertical handle orientation. Inlet / outlet diameter: 1-1/2".

Neoprene. 12 blades. Diameter: 2-1/4".

Nitrile. 12 blades. Diameter: 2-1/4".

Replacement for the Jabsco 836-0001 impeller. Only impeller able to run dry for 15 minutes Globe impellers are made of Brandonite a high-strength, elastomeric material with self-lubricating compounds for run-dry protection and improved resistance to sand and dirt to help keep you going in the most difficult conditions.

Cast bronze Cast hex for easier installation Curved 90 degrees Pipe Size: 1-1/4" Hose Size: 1-1/4" Overall Length: 5-1/2" Weight: 1 lb

Neoprene. 10 blades. Diameter: 2-9/16".

Replacement for the Jabsco 920-0001 and Johnson 09-1028B impellers. Only impeller able to run dry for 15 minutes Globe impellers are made of Brandonite a high-strength, elastomeric material with self-lubricating compounds for run-dry protection and improved resistance to sand and dirt to help keep you going in the most difficult conditions.

For use with water drainage. Resistant to chemicals, heat, cold, ozone, saltwater. Temperature range: -40° to -210° F. Color: Black. Diameter: 5/8".

Cast bronze. Diameter: 3/4".

Double-ply soft wall, no wire.
For straight connection in wet exhaust systems.
Okay for either gasoline or diesel engines.
Designed for coolant and heat resistance.
Color: Black with blue stripe.
Temperature range: 0° to 212° F.
Diameter: 4".
Length: 12.5 feet.

Designed to remove water from basements, garages, stairwells, utility rooms, back yards, sumps, pools, pool covers, boats and more.
Fully-automatic version uses standard 110 volt AC current
8' cord.
1800 GPH.

316 stainless steel. 90 degree bend. Size: 1-1/2" NPT.

316 stainless steel. 90 degree bend. Size: 1-1/4" NPT.

Provides pumping power at the push of a button. Has a connection for a vacuum switch accessory. Bronze construction. Mechanical seal, stainless steel shaft. 1-1/2" ports.

Replacement for the Jabsco 1210-0001 and Johnson 09-1027B-1, 09-1027B-10 impellers. Only impeller able to run dry for 15 minutes Globe impellers are made of Brandonite a high-strength, elastomeric material with self-lubricating compounds for run-dry protection and improved resistance to sand and dirt to help keep you going in the most difficult conditions.

Replacement for the Jabsco 6303-0001 and Johnson 09-824P-9 impellers. Only impeller able to run dry for 15 minutes Globe impellers are made of Brandonite a high-strength, elastomeric material with self-lubricating compounds for run-dry protection and improved resistance to sand and dirt to help keep you going in the most difficult conditions.

Direct-sight mechanical tank sending unit.
A replacement fuel gauge.

A lighter, compact pump for smaller vessels.
Tough plastic body with integral strainer.
Quick-release inlet strainer allows for quick cleaning.

12 volt DC.
3/4" hose connections.
Output: up to 23 liters per minute.

Includes a Rule 35A non-mercury float switch.

A compact, general-purpose pump. Bronze body. Nitrile impeller. 3/8" ports. Rated for 3.4 gallons per minute at 10 feet. Stainless steel shaft. 6 foot cord, with AC plug.

For use with sinks, showers, drain lines, pumps, AC systems. Resists mild chemicals, heat, cold, ozone, saltwater. Designed for flexibility and heavy-duty suction. Color: Clear blue spiral. Diameter: 3".

For use with sinks, showers, drain lines, pumps, AC systems. Resists mild chemicals, heat, cold, ozone, saltwater. Designed for flexibility and heavy-duty suction. Color: Clear blue spiral. Diameter: 2".

For use with sinks, showers, drain lines, pumps, AC systems. Resists mild chemicals, heat, cold, ozone, saltwater. Designed for flexibility and heavy-duty suction. Color: Clear blue spiral. Diameter: 1".

Full flow. Bronze construction. Dimensions: 3/4" NPT to 1" hose.

For use with 1 to 5 gallon accumulator tank Designed for 6 or more fixtures Quiet smooth flow No harm if runs dry. Strainer included. Plug-in ports, easy install: 2 for garden hose and 2 for 3/4" hose barb. Weight: 6 lbs

Single-layer, corrugated polyethylene hose.
Resistant to mild chemicals and salt water.
Has a clamping cuff every foot.
This hose is primarily used for bilge pump discharge.
Diameter: 1-1/4".
Color: Black.

Heavy-walled FDA-approved vinyl compound. Reinforced with polyester braid. Non-toxic, tasteless, odorless. Red tracer in clear PVC. Appropriate for: - Hot/cold pressurized water systems - Vent and drain lines - Bilge pump discharge. For temperature range: 25° F - 150° F. Rated for a burst pressure of 250 psi. Size: 3/4".

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 7/8". Length: 12.5 feet.

316 stainless steel. 90 degree bend. Size: 2" NPT.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 2-1/2". Length: 12.5 feet.

Electromagnetic clutch pumps equipped with a powerful electric clutch for convenient remote operation 12 volt pump Capable of operating through a wide range of speeds and in either rotational direction. Dimensions: 2A Pulley Belt Grooves - 2" NIPT - 83 GPM Weight: 30.5 lbs

Diameter: 5/8". 50 foot coil.