Nitrile. 6 blades. Diameter: 1-1/4".

Midland Metal flare reducer. Brass construction. 3/8" MSAE to 1/2" FSAE. Weight: .05 lb.

Neoprene impeller for Sherwood 10615.

Fynspray rocker action pump.
May be used with either fresh or salt water.
Self-priming.
Tough non-corrosive white plastic and chrome steel.

For venting bilge gases and fumes.
PVC hose supported by helical wire.
Resistant to ozone, sunlight and weathering.
Will not support a flame.
Diameter: 3".

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 4". Length: 12.5 feet.

Fynspray rocker action pump. May be used with either fresh or salt water Self-priming. Tough non-corrosive black plastic and chrome steel. Weight: 1 lb.

For reducing pipe diameter.
Size: 2" X 1-1/2".
Manufactured from 304 stainless steel.

Stainless steel pipe cap. 1/2" standard. Rated for 3000 PSI.

Fire-retardant marine fuel hose. Resists alcohol-enhanced gasolines. High nitrile rubber construction. Reinforced with two spirals of synthetic fabric. Diameter: 3/8". 250 feet per spool.

Fire-retardant marine fuel hose. Resists alcohol-enhanced gasolines. High nitrile rubber construction. Reinforced with two spirals of synthetic fabric. Diameter: 3/8". 50 feet per box.

A metal sleeve with screw threads.
For reducing pipe diameter.
Manufactured from 304 stainless steel.
Size: 3/4" X 1/2".

Delrin plastic. Straight 1-1/4" drain. Includes nut.

For Jabsco pumps. Three per bag.

Hose to pipe adapter fitting.
316 stainless steel.
Diameter: 1-1/2".

Use for engine cooling, wash down, circulation, and general purposes on-board or dockside Self-priming with ability to operate in either direction at variable speeds Removable end cover for easy impeller service 83 GPM - 2" NIPT - 1" diameter shaft Weight: 21 lbs

Hose to pipe adapter fitting.
316 stainless steel.
Diameter: 1-1/4".

Hose to pipe adapter fitting.
316 stainless steel.
Diameter: 1".

Full flow. Bronze construction. Dimensions: 1" NPT to 3/4" hose.

For reducing pipe diameter.
Size: 1-1/4" X 1"
Manufactured from 304 stainless steel.

For reducing pipe diameter.
Size: 1-1/2" X 1".
Manufactured from 304 stainless steel.

Built from neoprene for maximum endurance and performance. Replaces standard impeller (Quicksilver #47-59362).

Non-automatic; used with a panel and/or float switch.
Submersible and ignition protected.
High-efficiency, low-amp motor (1.6 amps at maximum flow).
Designed not to "burn out" when dry.
Stainless steel shaft.
Includes a back flow prevention device.
Model: 25DA.
Rated for 500 GPH.
3/4" port.
12 volts.

Self-priming drill pump chucks into a standard 1/4" drill motor and pumps up to 3 1/2 GPM (13 L/min). Use for draining engine oil through dipstick tube, pumping, and scavenging jobs, many uses around boat or home. Includes two 3/4" (19mm) garden hose port adaptors mounted on 1/2" barbed port. Weight: .36 lb

300 PSI gauge.
20" QCC pigtail hose included.
Wall mount, single stage.
Meets ABYC standard.

For use in extreme temperature conditions. 
Inner tube is red heat-resistant silicone. 
Reinforced with nylon fiber. 
Cover is heat and weather-resistant silicone. 
ID: 3/8". 
Rated for 80 PSI.

Automatic; no float switch needed.
Checks for water every two and a half minutes.
Runs for 1/2 second.
Consumes .2 amps per day.
Submersible and ignition protected.
High-efficiency, low-amp motor (1.6 amps at maximum flow).
Designed not to "burn out" when dry.
Stainless steel shaft.
Includes a back flow prevention device.
Model: 25SA.
Rated for 500 GPH.
3/4" port.
12 volts.

Full flow. Bronze construction. Dimensions: 1" NPT to 1-1/8" hose.

High-density unbreakable polyethylene.
Reversible self-venting spout.
Color: Light blue.
Dimensions: 15-1/4" X 10-1/2" X 14-1/2".
Capacity: 5 gallon.

Rated for 13 gallons per minute. Self-priming from up to 7.8 feet. 1" hose barb ports. 12 volts.

Cast bronze These valve bodies are offered to meet the needs of applications that require extra long, scoop or flush type thru-hulls Flange Diameter: 3-1/4" Pipe Size: 3/4" Weight: 2.5 lbs

Diameter: 1/8". 50 foot coil.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 3/4". Length: 12.5 feet.