For sanitation system connections. Multi-purpose, smooth-walled hose. For bilge, drain, or potable water uses. Temperature range: -13° to 158° F. Diameter: 1-1/8".

For Jabsco pumps. Three per bag.

5 feet long.
High-pressure rated.
3/8" female swivel flare end fittings.
UL 21 listed.

For Jabsco 17954-0001. Designed to run dry for 15 minutes. Dimensions: 2-5/8" X 2". 3/4" shaft diameter.

Heavy-walled FDA-approved vinyl compound. Reinforced with polyester braid. Non-toxic, tasteless, odorless. Red tracer in clear PVC. Appropriate for: - Hot/cold pressurized water systems - Vent and drain lines - Bilge pump discharge. For temperature range: 25° F - 150° F. Rated for a burst pressure of 250 psi. Size: 1-1/4".

For use with 1 to 5 gallon accumulator tank Designed for 6 or more fixtures Quiet smooth flow No harm if runs dry. Strainer included. Plug-in ports, easy install: 2 for garden hose and 2 for 3/4" hose barb. Weight: 6 lbs

Neoprene. 9 blades. Diameter: 2".

Brass nipple.
1" to close.

Brass nipple.
1" X 4".

Heavy-walled FDA-approved vinyl compound. Reinforced with polyester braid. Non-toxic, tasteless, odorless. Red tracer in clear PVC. Appropriate for: - Hot/cold pressurized water systems - Vent and drain lines - Bilge pump discharge. For temperature range: 25° F - 150° F. Rated for a burst pressure of 250 psi. Size: 1-1/2".

Rated for 5 gallons per minute. 70 PSI maximum pressure. Includes: - Pump - 25 feet of coiled hose - Pump protector inlet strainer - Spray nozzle - Two-way panel switch with fuse.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 2". Length: 12.5 feet.

Neoprene. 9 blades. Diameter: 3-3/4".

Nitrile. 9 blades. Diameter: 3-3/4".

304 stainless steel. 1-1/4" X 1-1/2".

Nitrile rubber. 10 blades Diameter: 1-19/32".

King Nipple - Straight Standard Flow 1/2" NPT x 1/2" hose - Bronze Weight .17 lbs

Dockside general purpose pumping and some onboard uses.
Self-priming and portable, very versatile.
Removable end cover allows easy impeller service.
Pump heads are built of bronze materials.

Single-layer, corrugated polyethylene hose.
Resistant to mild chemicals and salt water.
Has a clamping cuff every foot.
This hose is primarily used for bilge pump discharge.
Diameter: 1-1/8".
Color: Black.
50 feet per box.

For use with sinks, showers, drain lines, pumps, AC systems. Resists mild chemicals, heat, cold, ozone, saltwater. Designed for flexibility and heavy-duty suction. Color: Clear blue spiral. Diameter: 1-1/2".

For use with sinks, showers, drain lines, pumps, AC systems. Resists mild chemicals, heat, cold, ozone, saltwater. Designed for flexibility and heavy-duty suction. Color: Clear blue spiral. Diameter: 1-1/4".

Electromagnetic clutch pumps equipped with a powerful electric clutch for convenient remote operation 12 volt model Capable of operating through a wide range of speeds and in either rotational direction 2A Pulley Belt Grooves - 1" NIPT - 26 GPM Weight: 15.25 lbs

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 2-5/8". Length: 12.5 feet.

An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
Cycles every 2.5 minutes.
Fully automatic, doesn't require float switch.
High efficiency, low amp motor
Quick-release strainer allows for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
Model number: 53S.
2000 GPH.

Heavy-duty for hot or cold water systems. Extra wall thickness increases kink resistance. FDA-approved virgin vinyl compound. Diameter: 1/4".

Cast aluminum king combination nipples. Hose diameter: 2" Thread size: 2"

Cast aluminum king combination nipples. Hose diameter: 1-1/2" Thread size: 1-1/2" Weight: .01 lbs.

Cast aluminum king combination nipples. Hose diameter: 1-1/4" Thread size: 1-1/4" Weight: .01 lbs.

High-capacity bilge pump, designed for the toughest applications.
An optimized impeller gives great flow at low amperage.
A built-in thermal cut-off protects pump and vessel.
Backflow preventer helps keep bilges dryer and cleaner.
Completely submersible, rust and corrosion proof.
Built-in strainer base snaps off for easy cleaning.
Includes both straight and 90° port attachments.
12 volts DC.
2" discharge outlet.
Model number: 56D.
Rated for 4000 GPH.

Cast aluminum king combination nipples. Hose diameter: 1" Thread size: 1"