Pacer's S Series self-priming centrifugal pump.
Lightweight and chemically resistant for general service.
Suitable for water, salt water, waste water, and mild acids and bases.
Constructed from polyester.
Stainless steel or non-metallic fasteners for resistance to chemical attack.
This model is equipped with a hydraulic motor.
Suction lift to 25 ft. (7.6m) vertical.
- Requires 9.5 GPM for maximum pumping capacity
- HP required is 5.0
- Up to 230 GPM
- Buna-N elastomers
- Port size : 3" FNPT.

Designed to connect a tank to a wall mount regulator.
High-pressure rated.
Male POL to 1/4" inverted flare.
Length: 20".
UL listed.

Traps dirt and metallic particles. Lets you immediately inspect your fuel condition. Not for use on inboard engines. Includes connection barbs in 1/4", 5/16", 3/8".

Hose to pipe adapter fitting.
316 stainless steel.
Diameter: 2".

For sanitation system connections. Multi-purpose, smooth-walled hose. For bilge, drain, or potable water uses. Temperature range: -13° to 158° F. Diameter: 1".

Replacement impeller for Jabsco pumps.
(For 50410.)

Cast bronze Cast hex for easier installation Curved 90 degrees Pipe Size: 2" Hose Size: 2" Overall Length: 7" Weight: 2.5 lbs

Cast bronze Cast hex for easier installation Curved 90 degrees Pipe Size: 2-1/2" Hose Size: 2-1/2" Overall Length: 8-1/2" Weight: 3.875 lbs

A metal sleeve with screw threads.
For reducing pipe diameter.
Manufactured from 304 stainless steel.
Size: 3/8" X 1/4".

Replacement filter for 7852 Separator 28 micron Weight: 1 lb

A metal sleeve with screw threads.
For reducing pipe diameter.
Manufactured from 304 stainless steel.
Size: 1/2" X 3/8".

Neoprene. 10 blade. 2" diameter. Includes gasket.

Nitrile. 10 blade. 2" diameter. Includes gasket.

Cast bronze. Diameter: 1-1/2".

Designed for engine intake, bilge discharge and other lines.
Reinforced with wire helix embedded in synthetic material.
Excellent flexibility and bend radius.
Resists heat, fumes, ozone, acid, salt water and abrasion.
Color: Black with blue stripe.
Diameter: 1".
Length: 50 feet.

Designed for the tough demands of the fishing industry. Equipped with a liquid-cooled 12-pole motor. Features a mechanical shaft seal and a threaded port. Uses 1-1/2" and 2" ports. Rated for 4000 GPH.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 2-3/4". Length: 12.5 feet.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 1". Length: 12.5 feet.

Solid brass swivel fittings.
One side is 1" 20 female for a tee connection; other side is 1" 20 male with O-ring and check valve for an appliance connection.
This hose will connect with gas grill adapter tees.
Fully assembled and leak tested.
Length: 6 feet.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 2-3/8". Length: 12.5 feet.

Stainless steel housing and polyester internal parts. Dual 1-1/2" female and 2" male suction and discharge ports. Rated for 3450 RPM.

Dickinson propane connector hose. For use with small and large Sea-B-Que grills. Connects Sea-B-Que grills to standard propane tanks. Eight feet long. Part # 15-189. Weight: 1 lbs.

Dickinson propane connector hose. For use with small or large Sea-B-Que grills Connects Sea-B-Que grills to standard propane tanks. Six feet long. Part # 15-188. Weight: 1 lbs.

Electromagnetic clutch pumps equipped with a powerful electric clutch for convenient remote operation 12 volt model Capable of operating through a wide range of speeds and in either rotational direction 2A Pulley Belt Grooves - 1-1/4" NIPT - 62 GPM Weight: 21.65 lbs

316 stainless steel.
90 degree bend.
Size: 2" NPT.

Can deliver almost 7 GPM at open flow.
Equipped with pressure-cast bronze body.
Features a reusable O-ring type end cover seal.
1/2" internal pipe thread and 1" external hose barb.
Includes 2 port adapter.

Electromagnetic clutch pumps equipped with a powerful electric clutch for convenient remote operation 12 volt model Capable of operating through a wide range of speeds and in either rotational direction 1b Pulley Belt Grooves - 1-1/4" NIPT - 62 GPM Weight: 22.8 lbs

Long life circulation, high efficiency and flow Use for hot and cold water systems, live well and bait tank systems, liquid transfer also windscreen washing 3/4 " NPT or BPS Dimensions: 6" L x 6-1/2" W x 5" H Weight: 4 lbs

Provides high pumping capacity and reliability.
All-in-one pump and intelligent switch.
Designed to activate at 2-1/2" deep water.
Circuit will automatically cycle when needed.
1-1/8" discharge outlet.
12 volts DC.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 1-1/2". Length: 12.5 feet.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 1-1/2". Length: 12.5 feet.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 1-1/4". Length: 50 feet.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 1-1/8". Length: 12.5 feet.

Built from stainless steel and sturdy plastic. Features dual-heating design, both electrical and indirect. Thermostat is fully adjustable for safety. Uses polyurethane foam heat insulation. 5.81 gallon capacity, 1200 watts. For 120 volt systems.

Cam screws for Jabsco pumps. Pack of three.