For reducing pipe diameter.
Size: 1-1/2" X 1".
Manufactured from 304 stainless steel.

Built from neoprene for maximum endurance and performance. Replaces standard impeller (Quicksilver #47-59362).

Non-automatic; used with a panel and/or float switch.
Submersible and ignition protected.
High-efficiency, low-amp motor (1.6 amps at maximum flow).
Designed not to "burn out" when dry.
Stainless steel shaft.
Includes a back flow prevention device.
Model: 25DA.
Rated for 500 GPH.
3/4" port.
12 volts.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 1/2". Length: 12.5 feet.

King Nipple - Straight Standard Flow 1-1/4" NPT x 1-1/4" hose - Bronze Weight .60 lbs

iL500 Plus pump. Suitable for diesel, salt or fresh water. Rated for 500 gallons per hour. Includes: - Pump - Spray nozzle - 4 meter cable with battery clips - 4 meter lay-flat hose. 3/4" ports. 12 volts.

Double-ply soft wall, no wire.
For straight connection in wet exhaust systems.
Okay for either gasoline or diesel engines.
Designed for coolant and heat resistance.
Color: Black with blue stripe.
Temperature range: 0° to 212° F.
Diameter: 3-1/2".
Length: 12.5 feet.

Direct sight gauge. Gathers fuel level information with the float. Accurate gauge will fluctuate as the fuel "sloshes". Length: 17-3/4".

Use for engine cooling, wash down, circulation, and general purposes on-board or dockside Pedestal mount, corrosion resistant bronze pumps Self-priming and portable, very versatile Removable end cover allows easy impeller service Pump heads are built of bronze materials 62 GPM, 1-1/4" NIPT Port, 1" shaft, face seal, brass cam and impeller insert Weight: 12.6 lbs

Replacement for the Jabsco 18838-0001 impeller. Only impeller able to run dry for 15 minutes Globe impellers are made of Brandonite a high-strength, elastomeric material with self-lubricating compounds for run-dry protection and improved resistance to sand and dirt to help keep you going in the most difficult conditions.

Replacement for the Sherwood 17000 impeller. Only impeller able to run dry for 15 minutes Globe impellers are made of Brandonite a high-strength, elastomeric material with self-lubricating compounds for run-dry protection and improved resistance to sand and dirt to help keep you going in the most difficult conditions.

For use with 1 to 5 gallon accumulator tank. Designed for 6 or more fixtures. Quiet, smooth flow. Not harmed if it runs dry. Strainer included. Plug-in ports, easy to install. May be attached to garden hose or 3/4" hose barbs.

For use in extreme temperature conditions
Inner tube is heat-resistant silicone.
Reinforced with nylon fiber.
Cover is heat and weather-resistant silicone.
ID: 3/4".
Rated for 70 PSI.

1.24 CID hydraulic motor. 1-1/2" NPT impeller pump. 2000 maximum RPM. +/- 70 GPM of water at 2000 RPM. 11 GPM of oil required to achieve 2000 RPM. Aluminum bracket.

1.24 CID hydraulic motor. 1-1/4" NPT impeller pump. 2000 maximum RPM. +/- 55 GPM of water at 2000 RPM. 11 GPM of oil required to achieve 2000 RPM. Aluminum bracket.

Designed for engine intake, bilge discharge and other lines. Reinforced with wire helix embedded in synthetic material. Excellent flexibility and bend radius. Resists heat, fumes, ozone, acid, salt water and abrasion. Color: Black with blue stripe. Diameter: 1-5/8". Length: 12.5 feet.

Can deliver almost 7 GPM at open flow. Equipped with pressure-cast bronze body. Features a reusable O-ring type end cover seal. 1/2" internal pipe thread and 1" external hose barb. Includes 2 port adapter. 12 volt DC. Weight: 6.06 lbs

Oil resistant nitrile impeller or 6050 and 6850 Weight: .495 lb

Designed for the tough demands of the fishing industry. Equipped with a liquid-cooled 12-pole motor. Features a mechanical shaft seal and a threaded port. Uses 1-1/8" ports. Rated for 1600 GPH.

Clear plastic. Designed for easy inspection. Diameter: 3/8".

Designed for automatic operation with an Ultima switch.
Rated for 1000 GPH.
Equipped with easy-to-install Dura-Port discharge ports.
3/4" fitting.

Rated for high temperature. Diameter: 3".

Cast bronze. Diameter: 1".

Double-ply soft wall, no wire.
For straight connection in wet exhaust systems.
Okay for either gasoline or diesel engines.
Designed for coolant and heat resistance.
Color: Black with blue stripe.
Temperature range: 0° to 212° F.
Diameter: 3".
Length: 12.5 feet.

Provides high pumping capacity and reliability.
All-in-one pump and intelligent switch.
Designed to activate at 2-1/2" deep water.
Circuit will automatically cycle when needed.
1" and 1-1/8" discharge outlets.
12 volts DC.

Nylon pump body. Rated for 3.5 gallons per minute. Activates at 25 PSI, cuts out at 40 psi. Quiet operation, smooth flow. Compact design. 3/8" port, 1/2" hose output. 12 volt DC.

Johnson Aqua Jet water pressure system. A postive displacement diaphragm pump for small craft. Works great for pressurized water supply systems. Rated for 3.5 GPM. 3/8" NPT, 1/2" hose ports. Weight: 5.5 lbs.

Diameter: 3/16". 50 foot coil.

Replaceable wear plate to extend service when handling abrasive fluids
9.5 GPM - 115 Volt Motor - 1/3 HP - 1/2" NIPT
Dimensions: 7-3/4"H x 7-1/4"W x 10-1/2"L

Jabsco 50890 waste pump. A single-diaphragm, 5 GPM plastic-body pump. This self-priming pump is designed to pass debris. No filter required. OK to run dry and equipped with a 360º rotatable head. 12 volt.

Clear plastic. Designed for easy inspection. Diameter: 5/16".

Thermoplastic pump body. Rated for 5 gallons per minute. Stainless steel shaft. 3/4" ports. 12 volts DC.

Black smooth vinyl cover with a helix. Rated for full vacuum. Resistant to chemicals and saltwater. Primarily used for bilge pump and discharge purposes. Easily bent, OK for below waterline connections. Diameter: 1-1/8".

Prevents damage to lines due to rubbing and chafing. Color: Blue. 2-1/2" filled. 4" flat.