Nylon construction.
Designed with a molded-in recess in the base.
Provides a watertight seal.

SecureStack fuel tank - 6 gallon. "An innovative tank for today' boater." Ergonomic-designed, stackable, EPA compliant. The answer to your fuel handling problems.
NOTE: Due to the size of this product, shipping UPS or USPS may be cost prohibitive.  Please contact Seattle Marine at 1-800-426-2783 for shipping options.

Fuel tank tie-down strap kit. Includes: - Two 68" nylon straps - Four stainless steel tie-downs - Eight stainless steel mounting screws. Weight: .2 lb.

Stamped 304 stainless Dimensions: 1-5/8" x 1-3/4" Weight: .01 lb

Stamped 304 stainless Dimensions: 2-1/4" x 2-1/8" Weight: .03 lb

Stamped 304 stainless Length: 7" Width: 5-3/4" Weight: .58 lb

Single-layer, corrugated polyethylene hose.
Resistant to mild chemicals and salt water.
Has a clamping cuff every foot.
This hose is primarily used for bilge pump discharge.
Diameter: 5/8".
Color: White.

Cast bronze Hose size: 1-1/4" - Length: 4-1/2" - Width: 2-3/4" Weight: 1.375 lb

Stamped 304 stainless Length: 7-1/2" Width: 6-3/4" Weight: .79 lb

Smooth cover, clear PVC with white vinyl helix. Rated for full vacuum. Resistant to mild chemicals and saltwater. Used for: - Bilge pump intake and discharge - Livewell intake and drain - Sanitation: intake, vent and pump out. Designed for connections below the waterline. Not for use in pressurized systems or with antifreeze. Diameter: 3".

PVC. Male 1-1/4" to MNPT.

Labeling kit for marine manifolds. Great for labeling your SeaTech manifold.

PVC. 3" dust cap.

Cast bronze construction. Designed for easy installation and cleaning. Cast lugs on both sides for mounting. Four outside tie rods. Drain plug to remove sediment. Stainless steel strainer basket helps minimize electrolysis. Hinged lugs on cover for easy cleaning of basket. Pipe size: 3/4". Height: 8-3/8".

Washdown water outlet. Cast from 316 stainless steel. Allows for garden hose hookup to onboard water system. Standard male hose connector. Requires a separate ball or gate valve to regulate flow. 1/2" FIPT X 3/4 MGHT. Weight: .32 lb.

For Jabsco pump. Includes impeller, gasket, hardware.

For pedestal-mount pump. Includes impeller, gasket and hardware.

For Perko raw water strainers. Includes 1/2" and 3/4" gaskets. For #4 and #5 strainers.

Includes: - One cover gasket - Two cork cylinder gaskets. For use with #4 and #5 water strainers.

Cover bolt, wing-nut and washer. For use with 493 series water intake strainers. Fits models 4 and 5 only. Bolt length is 1-7/8".

Includes impeller, O-rings and seals.

Thru-Hull Connection for use with hose. Plain Bronze. (Not for use below waterline) Hose size: 5/8", Flange: 1-5/8", Max hull thickness 1-1/4" Back-side of flange is machined to fit hull and grooved to retain bedding compound.

For Jabsco manual pump toilet #29090. Includes gaskets and hardware.

Replacement pump end cover, for Jabsco pump, model 2760.

For hydraulic systems. Copper alloy wetted parts. Lower mount process connection. Displays 0 - 5000 psi.

Stamped 304 stainless Diameter: 4" Weight: .16 lb

Cast bronze. Diameter: 1-1/4".

Stamped 304 stainless Length: 5" Width: 4-5/8" Weight: .35 lb

Stamped 304 stainless Length: 5" Width: 9" Weight: .4 lb

PVC. Male 1-1/4" to hose.

Hydraulic Test Pressure 1/2" Carbon steel 1-piece body - Reduced bore. Blowout-proof stem - Screwed ends. Hi-Press Ball Valves (Steel or SS) 1/2 Steel 2,000 PSI

Brass and rubber construction. Diameter: 3/8". Snap lock handle is adjustable to tighten plug. Sized to fit most bait wells. Display packaged.

Hydraulic Test Pressure 3/4" Carbon steel 1-piece body - Reduced bore. Blowout-proof stem - Screwed ends. Hi-Press Ball Valves (Steel or SS) 3/4 2,000 PSI

Vent cap assembly for Forespar vented loops. "Duck bill" style. Commonly used in marine toilet or engine cooling systems. Molded from corrosion-proof Marelon. Manufacturer number: 903002 MF-841.

Gives structural stability in valve / thru-hole locations. Bottom port has straight threads to mate with thru-hulls. Top port has tapered threads to mate with ball valves. Use where in-line valves have been used as seacocks. Size: 2". Weight: 2.04 lbs.

For Jabsco impeller pump, model 9040.