Bronze construction. Nitrile impeller. Lip seal, stainless steel shaft. 1/2" ports, horizontal orientation.

Multiple flow control settings. Can work with both fresh and salt water. Designed for use with washdown pumps.

Easy way to remove impellers from pumps. For smaller impellers, less than 2-1/4".

Neoprene. 10 blades. Dimensions: 2-9/16" X 2". 5/8" shaft diameter.

For 12500 and 17000 series macerator pumps. Includes rubber seal and metal retainer.

Designed to remove water from basements, garages, stairwells, utility rooms, back yards, sumps, pools, pool covers, boats and more.
Fully-automatic version uses standard 110 volt AC current
24' cord.
1800 GPH.

Brass construction. For 2" pump.

Dash alarm for Rule bilge pump.
12 volts.
Does not include bilge pump switch. 

Jabsco ballast impeller. For use in Jabsco ballast puppy pumps. A nitrile polymer replacement impeller. Shaft diameter: 5/16". Impeller diameter: 2".

Neoprene. 6 blades. Diameter: 2".

Nitrile. 6 blades. Diameter: 2".

For Jabsco pumps. Includes impeller, O-ring, seal.

Robust Y valve allows waste to be pumped overboard or into a holding tank. Waste and corrosion resistant Rotating parts allow variable routing of hoses on valve Optional handle extension allows operation through bulkhead Can be padlocked to insure local regulations are met 1-1/2" Inlet or 1" outlet Dimensions: 7-5/8" L x 7-1/4" W x 4-1/8" H Weight: 1.9 lb

Non-automatic.
Rated for 900 gallons per minute.
Designed to bring pumping power to tight spaces.
Equipped with a backflow prevention valve.
For horizontal or vertical mounting.
12 volt DC.

Automatic.
Rated for 900 gallons per minute.
Designed to bring pumping power to tight spaces.
Equipped with a backflow prevention valve.
For horizontal or vertical mounting.
12 volt DC.

Float switch and an in-dash gauge. Gives a visual and audible alarm. Allows an unmanned compartment to be constantly monitored. For more compartments, add more float switches. 12 volt.

Impeller for GM engine 17360 Neoprene Weight: 1.08 lb

Included check valve prevents backflow.
Threaded discharge for easy installation and maintenance.
Connectors: 3/4" and 1".
Rated for 800 GPH.
May be operated by a separate panel switch or a float switch.
12 volt DC.

Major repair kit for Jabsco toilet. Includes seals and gaskets.

Nitrile impeller.
115 vac.
Rated for 6 gallons a minute.
Easy to service and maintain.
Tolerates fairly abrasive wear.

Nitrile rubber. 8 blades. Diameter: 2-9/16".

Neoprene. 8 blades. Diameter: 2-9/16".

For 18685 vane pump. Includes impeller, gasket, lip seal.

Pump with neoprene impeller Bronze body - Stainless steel shaft Stainless steel lip or mechanical seals for shaft Shielded ball bearings - 1" IPT Weight: 6.2 lbs

Automatic bilge pump.
1-1/8" discharge outlet.
Senses when bilge water reaches 2-3/4".
12 volt DC.
Rated for 1100 GPH.

A compact pneumatic bladder tank for small water systems. Smoothes water flow and eliminates pulses. Pressurized tank is rated to 20 PSI. Mounts easily in any position. Includes snap-in barbed or threaded hose fittings. Diameter: 4-3/4" Height: 13-1/4".

For use with 4" ducting. Output: 250 cubic meters per minute. Designed for flexible mounting. Simple slip-on inlet ducting connection. Corrosion-resistant. 24 volts DC.

Accumulator Tank Accumulator Tank Pneumatic accumulator tank for smooth flow from faucets & shower. Reduces pump cycling. Eliminates pulsations & water hammer. Water separated from air chamber by diaphragm & polypro tank liner. Tank volume: 2 gallons with working water volume of about 1 gallon. Mounts horizontally or vertically, even upside down. Port is 3/4" NPT (male). Includes brackets & band clamps. Pre-pressurized to 20 psi. Tank may be fine tuned to cut-in pressure of pump. Diameter: 8" (203mm). Height: 12 5/8" (320mm. Weight: 5 Lb. (2.3 kg). Max working pressure 100 PSI: (690 kPa).

Replacement clutch assembly for Jabsco pumps. "A" style grooves. For use with a 3/4" tapered shaft. 12 volt.

Float switch and an in-dash gauge. Gives a visual and audible alarm. Allows an unmanned compartment to be constantly monitored. For more compartments, add more float switches. 32 volt.

For Jabsco pumps. Three per bag.

Neoprene. 8 blades. Diameter: 1-1/4".

Nitrile. 8 blades. Diameter: 1-1/4".

For use with 4" ducting. Output: 250 cubic meters per minute. Designed for flexible mounting. Simple slip-on inlet ducting connection. Corrosion-resistant. 12 volts DC.

A compact multi-purpose hand pump kit. Great for many draining and liquid transfer jobs. Small enough to fit in a tool or tackle box. Includes: - Pump - 2" hose - Draw tube for draining crankcases.